接线柱

浅谈主变接线柱磷铜浇铸钎焊技术的应用

Application of Main Transformer Terminal Phosphorized Copper Cast Brazing Technique

那个红电线接在正极接线柱上，明白了吗？

The red wire goes to the positive terminal . Get it ?

请务必将本仪器的背面接线柱的E端直接与大地连接。

Be sure to connect copies of the back E end of binding post of instrument with earth directly .

形成倒装芯片焊点的铜接线柱焊凸（SBC）法

Solder Bump on Copper Stud ( SBC ) Method of Forming the Solder Joint in Flip Chip

如果接线柱被腐蚀，就要清洗。

If the terminals are corroded , clean them .

你可以在安装在墙上的大型布线上找到接线柱成为终端盒。

You 'll find binding posts on huge wall-mounted things called terminal boxes .

一种便于现场更换的新型低压接线柱导电杆

New Low-Voltage Connection Conductive Rod Replaced Easily on Field

接线柱自动送料切槽切断级进模设计

Design of Progressive Die with Automatic Feed for Grooving and Cut-off of Junction Pole

用钢丝刷清刷接线柱和夹子。

Clean posts and clamp with wire brush .

配备接线柱，安装快速、简易；

Install quickly and easily with junctions ;

配电箱接线柱编号与图纸上的编号不一致。

Serial numbers of termination in power distributing box not correspond with number in drawing .

GB14808-1993交流高压接触器灯体内装有镇流器、触发器和接线柱。

Alternating-current high-voltage contactors Ballast , ignitor and terminal pillars are installed in the body .

需要有一个能在其两个接线柱之间保持恒定势差的电源。

A source capable of maintaining a constant potential difference between its terminals is necessary .

本仪表装有保护环接线柱，用以纠正因表面漏电而造成的误差。

This tester is provided with a " Guard " terminal to prevent errors due to surface leakage .

带接线柱骨架的空心杯电枢制造中的模具设计

The Design of the Mould and the Fixtures in the Forming of the Coiling Armature with Fiber Plastic Skeleton

灯体内装有镇流器、触发器和接线柱。从车门上拆卸车门内侧手柄触发器。

Ballast , ignitor and terminal pillars are installed in the body . Remove door inside handle actuator from door .

在纽约曼哈顿我家中的地下室里有一些这种接线柱。

We have several in the basement of the building in Manhattan , New York , in which I live .

对电力配电变压器低压接线柱频繁烧损原因作了具体分析，由此提出了对低压接线柱结构进行改进的具体方案，设计出一种两段式新型导电杆。

The frequent damage of power transformer 's low-voltage connection pole is studied in detail and a solution to improve its structure is proposed .

被腐蚀的接线柱和接线夹会导致连接处的电压下降，从而降低蓄电池供电时的输出电压和充电时的输入电压。

Corroded terminals and clamps cause a voltage drop at the connection , which reduces the available voltage flowing both to and from the battery .

电子元件：生产各种系列的接线柱、险丝座、插件、频连接线、车点烟插头及插座等。

Electric components : This series include various kinds of terminal , fuse box , connector , wire bundle connection cables cigarette plug and socket for automobile , etc.

应用范围：主要应用于集成电路、继电器、接插件、锂电池、微波器件、传感器、钽电容器、压缩机接线柱等类产品中。

Application : mainly used in integrated circuit , relays , connectors , lithium batteries , microwave devices , sensors , tantalum capacitors , compressor terminals and other products .

在完成维修前，应正确清洁及检视电池固定夹、托架、端子、接线柱和顶端。欲知更多资讯，请参见本单元中的安装程序。

Clean and inspect the battery holddowns , tray , terminals , posts , and top before completing servicsee the battery removal and installation procedures in this group for more information .

检查方法是将兆欧表上的一个接线柱接在电泵电缆线上，另一接线柱接在电机外壳上，摇动兆欧表，观察绝缘电阻值。

Megohm inspection method is to form an electric cable terminal at the online access , another access terminal on the motor casing , megohm shake table to observe the value of insulation resistance .

连接条和接线柱的焊接必须使极柱顶部和盖子的铅衬套与连接条环口或接线柱完全熔焊牢固。

Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post .

分析了带接线柱骨架空心杯环氧浇注前成形的特点，介绍了该空心杯环氧浇注模的特殊模具结构设计，同时说明了模具工作过程。

The analysis of the forming characteristics of the coiling armature with fiber skeleton before pouring epoxy , the introduction of the specific structure of the epoxy pouring mould , and the explanation of the working procedure of the moulds .

免维护蓄电池与传统蓄电池相比具有使用中不需添加蒸馏水、接线柱免腐蚀、自放电量少、增设液体密度计电眼等优点。

Compared with the traditional one , the maintenance-free battery has many good properties such as free of adding distilled water no corrosion of the terminal , less amount of self-discharge and additional installation of an electric eye for the densimeter .

为电缆终端线夹和电池接线柱露出部分涂一层薄的凡士林油或车用底盘滑脂。

Apply a thin coating of petroleum jelly or chassis grease to the exposed surfaces of the cable terminal clamps and the battery terminal posts . A columnists on its pedestal . having columns either at both ends or at both sides .

预接线板接线柱，在电线上标记相关的仪器编号。

Pre-wire panel wiring to terminals , tag wires with associated instrument tag number .

汽轮发电机定子测温接线板上接线柱品目的识别网络终端上位机程序；

The Distinguishing Method of Two Kinds of Terminal Posts on the Temperature Measuring Terminal Board of the Turbogenerator Stator network terminal programmer ;

为了确保良好的电路连接状态，可以取下蓄电池接线夹，然后用一个专用工具清除接线夹和接线柱上的聚集物。

To ensure a satisfactory electrical connection , remove the battery clamps , then clean them and the terminals with a tool designed for this purpose .