成品退火

  • 网络final annealing
成品退火成品退火
  1. 铁含量较少时,在成品退火的低温阶段,形成回复亚晶组织;

    With less Fe , the substructure is formed during the low temperature stage of final annealing .

  2. 研究了深冲用3003-O铝合金带材合理的生产工艺,在化学成分和铸造、热轧、冷轧工艺确定的情况下,试验研究成品退火工艺制度。

    Studied the annealing institution of3003-O aluminum alloy strip for drawing is researched , while the chemical composition and casting , hot rolling , the cold rolling , process were determined .

  3. 成品退火工艺对高压光箔立方织构的影响

    Effect of Product Annealing Process on the Cubic Texture of High Voltage Foil

  4. 集成电路引线框架材料成品退火工艺探讨

    Making an Approach to Annealing Technology of Finished Products of IC-Lead Frame Materials

  5. 成品退火前铰链异型材除油脱脂装置的新设计

    New Design on Oil Removal Equipment for Profiled Hinge

  6. 选择合理的成品退火工艺是提高电缆铝箔力学性能的重要途径。

    Selection of proper product annealing process is an important way to improve mechanical property of the aluminum foil for electric cable .

  7. 结果表明,摩擦因数过大或过小均不利于主要轧制织及成品退火后立方织构的形成。

    The results show that neither too large nor too small friction coefficient were beneficial to the formation of copper texture and cube texture .

  8. 探讨了针布齿条热处理中原材料、半成品退火处理、成品的淬火处理的各种问题,同时提出了解决方法,以供同行参。

    Approach is done into the problems in process of annealing of raw material and semi-products and of quenching of finished products for manufacturing of card wires .

  9. 采用一次冷轧法可获得较好的综合磁性,适当提高成品退火温度可使不同状态热轧板成品性能基本趋于同一水平。

    The over-all properties can be obtained by using once cold rolling and the basic properties of different hot band condition can be homogenized by properly increasing temperature of final annealing .

  10. 探讨用铸轧坯料生产8011AO0.0115mm啤酒封用铝箔的生产工艺、中间退火制度和成品退火制度对铝箔力学性能和组织的影响。

    The influence of process , medium annealing , finally annealing on the structure , mechanical properties of 8011A aluminium foil for label on the bottle beer by cast-rolling stock were studied .

  11. 讨论了轧制工艺(换向工艺)、成品退火工艺对钼片性能(力学性能、深冲性能、硬度等)的影响。

    The effect of the rolling technology ( inverting techniques ) and final product annealing technology properties ( such as mechanical properties , deep-drawing property , hardness and so on ) of Mo sheets is discussed in this paper .

  12. 通过对热终轧温度不同的热轧板进行预备退火、冷轧和成品退火试验及成品立方织构的定量检测,研究热终轧温度、预备退火温度、成品退火工艺对立方织构比例的影响规律。

    By tests of preparing anneal , cold rolling , last anneal and quantitative measurement of cube texture for finished product , the effect rule of hot finish rolling temperature , preparing anneal temperature , last anneal technique on the cube texture ratio was obtained .

  13. 还推导出了毛细管管壁内任一点的径向位移公式,且据此说明了毛细管成品必须退火。

    In order to explain the importance of annealing for finished capillary the radial displacement formulation for any points on the capillary walls was derived .