槽模

cáo mó
  • flute cast;channel mould
槽模槽模
槽模[cáo mó]
  1. 大连地区某些石英岩底面的类似沟模、槽模现象

    Phenomena Similar to Groove Cast and Flute Cast at Bottom surface of Some Quartzites in Dalian Area

  2. 浊积扇相以发育槽模、正粒序、爬升波纹层理、包卷层理、双向交错层理、透镜状层理、平行层理为特征。

    The turbidite fan facies is characterized by flute cast , normal-graded bedding , climbing ripple lamination , convoluted lamination , bidirectional cross bedding , lenticular bedding and parallel bedding .

  3. 窄长厚壁冲槽模设计

    Design of the Die for Punching Narrow Slots in Thick Walls

  4. 变速器螺纹板切槽模设计

    Design of Cutting Slot Die for the Derailleur Screw Thread Plate

  5. 冲槽模的早期失效分析及热处理工艺改进

    Earlier Failure Analysis of Punching Slot Die and Improvement of Heat-Treatment Process

  6. 阳条砖(釉面砖的配件砖)槽模圈梁在多层砖混结构房屋中的应用

    Application of trough model loop girder in multiplayer building made of brick

  7. 槽模规模由东南向西北明显变小。

    The scale of the flute castes changes gradually small from southeast to northwest .

  8. 直线轴承外骨架拉伸模及侧面冲槽模设计

    Design of Drawing Die and Side Punching Die for the Outer Shelf of Linear Axletree

  9. 硬质合金轧辊开槽前的车削加工工艺联接头冲槽模结构改进

    Turning before notching groove in the roll Improvement of Notching Die Structure for the Joint

  10. 离合器盖内缘舌片弯曲压槽模设计

    Design of the Bending and Groove-Pressing Die for the Inner Tongue Piece of the Clutch Cover

  11. 介绍了拉深模、冲底孔、冲槽模及冲侧孔模的三种模具结构。

    Three kinds of mould structures were also introduced including drawing mould , punching bottom hole and punching groove mould , and punching side hole mould .

  12. 针对此工艺设计了翻边成形双槽模,并介绍了模具的结构特点及工作过程。

    A double_slot flanging forming die was designed according to this processing technology . And the characteristics of the structure of the die and its working process were introduced .

  13. 设计了一种在内孔为锥面圆管上冲窄面、厚壁的冲槽模,阐述了其设计原理,模具结构,工作过程及主要零件的设计要点,另简述了冲头强度的校核方法。

    A notching die for punching narrow face and thick wall on tube with cone hole is designed . Its design principle , die structure , work process and design gist of main parts are elaborated . The check method of punch strength is presented .

  14. 1394-VXI零槽控制器模件设计和实现

    Design and implementation of VXI slot 0 controller module with IEEE 1394 interface

  15. 嵌入式双圆槽拉伸模设计

    Design of the Drawing Die for the Embedded Double Circle Slot

  16. 蓄电池槽注射模设计

    Design of the Injection Mould for the Accumulator Tanks

  17. 音乐琴片窄长槽形模设计

    Design of the Narrow_Slot_ Shaped Die for the Strips of a Musical Instrument

  18. 接着,介绍了国产化零槽控制器模件的调试过程。最后,阐述了整个系统的测试过程。

    Then debugging of the module is described . The system test is introduced at last .

  19. 电机槽楔挤压模CAD系统

    The CAD System of Extrusion Die for Slot Wedge in Motor

  20. 镁电解槽的冷模实验与数值模拟研究

    The model experiment study on magnesium electrolyser

  21. 单槽冲模中凸模固定结构的改进

    Improvement in the Fixed Structure of the Punch of the Stamping Die with a Single Slot

  22. 阐述了槽型凹模拼块在加工时的工艺流程、工艺要求,以及槽型凹模拼块组装程序。

    The technology process , technology requirement and the assembling procedure of shaped groove die were also set forth .

  23. 对精锻模具的平衡角、毛边槽和分模线各参数进行了设计,并绘制了带阻尼台叶片工艺过程中的精锻模具。

    Several parameters of the forging die the equilibrium angle , the rough edge and the parting line are designed .

  24. 并结合一个应用实例来说明槽楔冷挤模CAD系统的应用。

    An example shows the application of the CAD of cold extrusion die for slot wedge .

  25. 筐形保持架无槽凹模压坡模的设计

    Design for concave die without slot and press die of box-type cage

  26. 接线柱自动送料切槽切断级进模设计

    Design of Progressive Die with Automatic Feed for Grooving and Cut-off of Junction Pole

  27. 虽经改进,在胎具上开空槽、增设导向模等,仍不能有效克服纬线张力造成的迟滞效应。

    The effect of slow moving resulted by tension force can also not effectively overcome , though the utility model is improved , comprising opening a dead slot on the mould and adding a direct die .

  28. 通过对微电机槽楔的特点和使用要求的分析,论述了槽楔冷挤模CAD系统的原理;

    The characteristics and instruction of part like slot wedge in micro motor are analyzed at first , and the principle about the CAD of cold extrusion die for slot wedge is discussed .

  29. 以电冰箱电机定、转子片槽型为例,介绍在多工位硬质合金级进冲模中,当槽型凹模采用拼块结构时,槽型凹模拼块的组成和数量的确定。

    Taking the stator and rotor slice with shaped groove of electric machinery of refrigerator as an example , when the shaped groove die adopts insert structure , the form and quantity of inserts were introduced .