150mm

Development and application on horizontal casting for φ 150mm round blank

φ150mm水平连铸圆管坯的开发与实践

Uncertainty evaluation of measure result of 14 ~ 150mm standard ring gauge

14～150mm标准环规测量结果的不确定度评定

Cause Analysis and Solving Measure of Shape Defect of 150mm × 150mm Continuous Casting Billet

150mm×150mm连铸坯形状缺陷的成因分析及解决措施

An aluminium casting ( 150mm ) image obtained by the system at accelerator high energy X-ray is offered .

给出了某铝铸件（厚150mm）在加速器高能X射线下的成像结果。

Cause for shape defects occurring on 150 × 150mm ~ 2 billets & countermeasures

150mm方坯形状缺陷的成因与对策

Research and practice of 150mm × 150mm billet rolling in the section mill of Anyang Steel

安钢型材机组采用150~2方坯轧材的探索与实践

Conveyor frame : 150mm formed channel frame , 5mm thick steel with heavy pipe dividers .

输送机车架：150毫米轨道形成框架，用5毫米厚钢板和厚壁管分隔开。

Fitting to lower melting point of tin-lead solder , the length of zone of heating is 150mm ;

由于含铅钎料熔点低，受热区长度只要150mm就可以了。

The paper describes the development , process and quality of horizontal casting for φ 150mm round blank at Hengyang Steel Pipe Group Co. , Ltd.

介绍衡阳钢管公司φ150mm水平连铸圆管坯的开发方案、生产工艺及铸坯质量。

Comes equipped with twin barrels ( 150MM ), dual missile pods for attacking infantry and aircraft , and lots of destructive firepower .

装备两门150毫米炮管，二重的导弹发射架以攻击步兵和飞机，有大量毁灭性火力。

In this paper , the properties of copper-bearing gold concentrates were discussed . Tests were carried on in a Φ 150mm fluidizing reactor with mixed gold concentrate samples as raw material .

本文阐述了含铜金精矿的性质，并以混合金精矿矿样为原料，在Φ150mm沸腾炉进行了焙烧试验。

Total base number of the product may be up to 350 ~ 580mg KOH / g , and its kinematic viscosity at 100 ℃ is 50 ~ 150mm 2 / s.

产品总碱值350～580mgKOH·g-1，而其100℃运动粘度可稳定在150mm2/s以下的较低范围内。

The prepared magnolol-bonded phase was packed into a stainless steel column ( 4.6i . d. × 150mm ) under constant pressure and used as analytical column for HPLC . 3 .

在恒压下将厚朴酚键合硅胶（MSP）填入不锈钢色谱柱（4.6i.d.×150mm）中，作为高效液相色谱分析柱使用。

In this paper , shearing test on 72 cube specimens ( 150mm × 150mm × 150mm ) with cutting groove bonding has been carried out , using the self-made shearing equipment .

采用自制的剪切夹具对72块150mm×150mm×150mm沟槽式新老混凝土粘结试件进行了抗剪试验。

At the base of that , the operation condition of HPLC method to determine DMY are immobile phase was Symmetry 300 ~ ( TM ) C_ ( 18 ) 3.5 × 150mm ;

在此基础上，建立了高效液相色谱法测定二氢杨梅素的操作条件。色谱柱为Symmetry300~（TM）C（18）3.5×150mm；

The analysis on the surface state and the element composition of T-1000 carbon fiber , and the property of its composite were performed by SEM , IR , XPS , Nol ring and Φ 150mm vessel .

用扫描电镜、红外光谱、X射线光电子能谱仪、NOL环及Φ150mm容器等手段，对T-1000碳纤维表面状态、元素组成和复合材料性能进行系统研究。

Through the improving project of film thickness uniformity on DYC-900 large caliber coating machine , the film thickness uniformity increase to 98 % in the cone radius of 0 ~ 150mm , which can satisfy the batch manufacture requirement of optical thin films .

通过对DYC-900型大口径镀膜机膜厚均匀性改进方案的提出和实验，使其膜厚均匀性在锥面径向0~150mm的范围内提升到98%，能够满足光学薄膜批量生产的要求。

Methods : Forsythin was quantified by a HPLC consisted of a C_ 18 column ( 150mm × 4.6 mm , 5 μ m ) and a mobile phase of acetonitrile-water ( 26 ∶ 74 ) with detection wavelength at 230 nm .

方法：采用HPLC法，色谱柱为C18柱（150mm×4·6mm，5μm），流动相为乙腈-水（26∶74），检测波长230nm。