首页 / 词典 / good

accu

  • abbr.蓄电池;accumulator 累加器
accuaccu
  1. Principle and Application of Accu Star ⅱ Dual Axis Level Sensor

    AccuStarⅡ型双轴水平传感器原理及其应用

  2. Automatic position control system for Φ 180 mm ACCU ROLL tube mill

    Φ180mmAccuRoll轧管机组自动位置控制系统

  3. The method is rapid and accu - rate , and suitable for .

    方法快速、准确,适于常规分析。

  4. Accu rate Diagnosis of Viral Hepatitis B and C

    走出慢性乙型、丙型病毒性肝炎诊断的误区

  5. Experiment on Lubricant for Guide Disk of Accu Roll Tube Mill

    AccuRoll钢管热轧机导盘工艺润滑油的试验

  6. NC - Aimed Process of Accu - Roll Pipe Mill Guide Dise

    AccuRoll轧管机组导盘的数控加工

  7. That is accu .. Yes , that is accurate , yes .

    这是确..是的,这是准确的,是的。

  8. Adjustment of the main drive reducer eccentric sleeve of both accu roll mill and piercer

    AccuRoll轧管机和穿孔机主传动减速机偏心套调整

  9. The accu - racy of wind tunnel experiment and aerodynamical curve are analysed .

    分析了风洞实验精度和气动力曲线。

  10. Source identification of PM_ ( 10 ) aerosol samples by ACCU sampler and PIXE technique

    ACCU采样和PIXE技术用于PM(10)污染溯源的研究

  11. Use of ACCU in particulate collecting

    使用ACCU单元采集空气中的颗粒物

  12. Owing to the application of computer and other intelligent instruments , the function and accu ˉ rate of dynamic balancing have been improved a lot .

    随着计算机及其他智能仪器在此领域的应用,动平衡的功效及精度已大大提高。

  13. The ACCU Series is an economical pneumatic linear actuator that contains an internal Linear Resistive Transducer ( LRT ) .

    在农民自卫队系列是一种经济的气动直线驱动器,其中包含一个内部线性电阻传感器(轻铁)。

  14. The method of NC - aimed process of Accu - Roll pipe guide dise , and how to improve quality and efficient in manufacturing .

    本文着重讨论了AccuRoll轧管机组导盘的数控加工方法,以及如何提高加工质量和加工效率。

  15. Presented in this article are the technological features and the rolling schedule-making of φ 114mm Accu Roll Pipe Mill .

    介绍了φ114mmAccuRoll轧管机的工艺特点,探讨了其轧制表的制定。

  16. Additionally , the ACCU Series is conducive where variations in cylinder stroke and speed are required or where an application calls for continuous position monitoring .

    此外,农民自卫队系列有利于凡在气缸行程和速度的变化要求或申请的位置连续监测要求。

  17. Computer software for simulating vertical section of deformation zone on Accu Roll rolling process developed on the basis of models built , which puts the base for optimizing process parameters .

    在建立Accu-Roll轧机变形区模型的基础上,开发出计算机模拟软件,可方便地通过变形区纵剖面计算机图象显示分析工艺参数对变形区的影响,从而为合理地选取与优化工艺参数提供依据。

  18. It is necessary to achieve reliable R wave detection performance and accu - rate peak point of R wave for the analyse of heart rate variability ( HRV ) .

    在心率变异分析中,不仅要可靠地检测出R波,而且要对R波的峰值点进行准确定位。

  19. Because there are two platforms , every bogie weight is calculated twice , and so the weighing accu - racy is better than that in one platform .

    因为有两个秤台,每个转向架被计量两次,这样,称量精确度比单秤台高。

  20. The paper introduces the design method about the controller three coordinates one wielding the simple hand movement using the digital electronic technology knowledge , check occasion very highly to accu - racy .

    该文介绍一款运用数字电子技术知识设计的简易手动三坐标控制器,该控制器主要应用于某些对精度要求不是很高的测量、检验场合。

  21. The article covers the technique of adjusting tooth engagement of the main drive reducer gear system of both Accu Roll Mill and Piercer by means of setting the eccentric sleeve .

    介绍了利用偏心套调整AccuRoll轧管机相穿孔机主传动减速机齿轮副啮合状态的工艺。

  22. The peak value of sediment concentration in gully runoff appears earlier than that of rainfall intensity , but in the runoff on accu - mulated steep slope it appears later .

    切沟的径流泥沙含量峰值先于雨强峰值出现,堆积陡坡坡面则滞后于雨强峰值;

  23. Conclusion : US has little value for those lesions . CT and MRI can show better about those lesions ' location , range , appearance , density and signal intensity . Multislice images and signal changes made MRI to be more valuable for diagnosis accu ˉ racy .

    结论超声的诊断价值有限,CT和MRI显示病变的位置、范围、形态、密度和信号较佳,多断面成像和信号变化使MRI在诊断中更有价值。

  24. And only take 7 tests of finger-tip blood glucose per day ( glucometer : ACCU produced by Roche ) for the patients in the control group . These tests are carried out before and 2 hours after the three meals , and right before sleeping .

    仅对对照组患者进行每天监测7次指尖血糖(指尖血糖仪:德国罗氏血糖仪):三餐前、三餐后2小时、睡前血糖。