首页 / 词典 / good

asperity

美 [æˈsperəti]英 [æˈsperəti]
  • n.严厉;(尤指语言、态度)粗暴

复数: asperities

asperityasperity

noun

U(尤指语言、态度)粗暴,严厉
the fact of being rough or severe, especially in the way you speak to or treat sb

harshness

asperity

频次

  • 1
    N-UNCOUNT (语气的)急躁,粗暴,严厉
    If you say something with asperity, you say it impatiently and severely.

    'I told you Preskel had no idea,' remarked Kemp with some asperity.

    “我告诉过你普雷斯克毫不知情的,”肯普颇为不耐烦地说道。

noun

1
harshness of manner
Synonym: sharpness
2
something hard to endure
the asperity of northern winters
Synonym: grimness hardship rigor rigour severity severeness rigorousness rigourousness

数据来源:WordNet

  1. He spoke to the boy with asperity .

    他严厉地对那男孩讲话。

  2. I said , with some asperity , that that was no concern of mine .

    我颇为粗暴地说,那跟我毫无关系。

  3. ' I told you Preskel had no idea , ' remarked Kemp with some asperity .

    “我告诉过你普雷斯克毫不知情的,”肯普颇为不耐烦地说道。

  4. Agglomerates of delusterant particles located near the surface of sythetic fibers cause asperities .

    消光剂颗粒集结在合成纤维表面附近,导致表面粗糙。

  5. " I didn 't enquire . " answered the doctor with some asperity .

    “我没有问。”医生回答得相当尖刻。

  6. The asperity of the winter had everybody yearning for spring .

    严冬之苦让每个人都渴望春天。

  7. If the gouge layer is thin , contact between asperities on the rock surfaces can occur .

    如果充填物层很薄,两个岩石表面上的凸起物就有可能互相接触

  8. An empirical Green function approach with asperity model considered

    考虑凹凸体理论的经验格林函数方法

  9. Main Bearing Lubrication Analysis Considering Crankshaft Elastic Deformation and Asperity Contact

    考虑曲轴倾斜和摩擦接触的主轴承润滑分析

  10. Characterizing a shallow earthquake asperity model for predicting near field strong ground motion

    近场强地震动预测中浅源地震的Asperity模型特征

  11. It is obvious that the asperity size effects on the amplitude spectrum .

    粗糙面的大小对振幅谱的影响不显著。

  12. A theoretical analysis of asperity contact is conducted for rolling point contact under oil lubrication condition .

    对油润滑条件下椭圆接触滚动表面的粗糙峰接触作了理论分析。

  13. Asperity load sharing of anisotropic rough surfaces in mixed lubrication

    混合润滑时各向异性粗糙表面微凸体载荷分配的研究

  14. An Experimental Study on Progressive Failure of Tooth-shaped Asperity Joints in Direct shear

    齿形节理渐进破坏直剪试验研究

  15. Numerical Analysis for Influences of Running in Process on the Lubrication Properties & Wear of Asperity and Profile

    磨合过程对润滑性能影响的数值分析&粗糙峰与轮廓的磨损

  16. A shallow earthquake asperity model for predicting near field strong ground motions was systematically characterized .

    系统地描述了近场强地震动预测中浅源地震的凹凸体模型特征。

  17. Study of rupture process and instability mode of step-like asperity on sliding plane in rock

    岩石错动面上阶梯形凸起的破裂过程与失稳型式研究

  18. Singularly Perturbed Solution of a Heavy Circular Plate Roll on the Asperity Plane Surface

    重圆盘在粗糙平面上滚动时的摄动解

  19. Effects of barriers and asperities on seismic moment

    障碍体和凹凸体对地震矩的影响

  20. Thicker films assure fewer asperity contacts and less wear .

    油膜越厚,摩擦越少,并且磨损越小。

  21. Numerical Analysis of the Transient Micro-EHL of Line Contact with a Single Asperity on a Surface

    一个表面带单粗糙峰的线接触时变微弹流润滑数值分析

  22. Phase Quadrature Laser Interferometer for Measuring Microscopic Asperity

    测量微观不平度的90°相移激光干涉仪

  23. The shear strength increases with the increasing first-order and second-order asperity heights and normal stress .

    节理剪切强度随着一阶和二阶起伏度及法向应力的增大而增大;

  24. " How strange ," continued the king , with some asperity ;

    “多妙呀!”国王用很尖酸的语气继续说道。

  25. Asperity Microcontact and Its Influence on Partial Hydrodynamic Lubrication of Rough Surfaces

    粗糙峰微接触及其对润滑的影响

  26. The principle and fabrication of the phase quadrature laser interferometer for measuring microscopic asPerity are described .

    叙述了测量微观不平度的90°相移激光干涉仪的原理和构成。

  27. Influences of the cavitations between the asperities on roughness surfaces on flow factors were investigated .

    研究了粗糙表面上微凸体间气穴对用于混合润滑分析的流量因子的影响。

  28. Undoubtedly , these asperities will have remarkable influence on surface friction and subsurface stress of the contact area .

    齿面粗糙峰的存在无疑会对齿面摩擦力和轮齿接触区次表面应力分布产生重大影响。

  29. The size of the peaks , or asperities , depends on the material and the method of surface finishing .

    峰或突起的大小与材料和表面抛光方法有关。

  30. Load Capacity of Asperities for Piston Ring-Cylinder Liner in Internal Combustion Engine at Running-in Stage

    内燃机缸套-活塞环磨合过程中微凸体承载研究