工作间隙

  • 网络working clearance;operation gap
工作间隙工作间隙
  1. 绞车盘形闸工作间隙检测传感器的研究

    Research on Detective Transducer for Working Clearance of Winch Disc Brake

  2. 在分析此方法可能导致的方程非收敛情况的基础上,改进了比例分割法,从而使有限元方程可以在整个工作间隙内得到有效的收敛解。

    Because of nonconvergent problem , the method was improved to get the true convergent root during the whole working clearance .

  3. 在设计过程中,讨论了MR液体工作间隙对阻尼器性能和阻尼器的两个重要指标:阻尼力大小和动力可调范围的影响,并得到了最为优化的工作间隙。

    In the course of the design , it is discussed that the working gap of MR fluid exerts influence on two key indexes of the damp force and dynamic range and the optimum gap size is calculated .

  4. 实验室测试证明,本系统能够在8mm磁芯工作间隙下,为负载提供48V/500W的直流电,总体效率在70%-75%之间。

    It proved that the UCLP system could supply 48V / 500W DC power over 8mm magnetic gap , with system efficiency ranging from 70 % to 75 % .

  5. 精密车床主轴轴承工作间隙的监测

    Monitoring for spindle bearing 's working clearance of precision lathe

  6. PJ&1型盘形闸工作间隙动态监测报警仪的设计

    Design of model PJ-1 dish-brake work-spacing in dynamic monitoring instrument with alarm

  7. 磁力研磨磁感应器工作间隙磁势计算

    The Magnetic Potential Computing of Working Gap in Inductor of Magneto-Abrasive Maching

  8. 水力增压器高压腔摩擦副工作间隙计算

    Working clearance of friction Pair in high Pressure chamber of hydraulic boosters

  9. 工作间隙适当的休息,能使你更加高效的工作。

    Taking a break from your work , can help you be more productive .

  10. 盘形闸工作间隙实时监测系统

    The Real-Time Monitor System for the Disc-Shaped Brake

  11. 拖动分子泵的压缩比&工作间隙的自泄漏模型

    Compression Ratio of Molecular Drag Pumps & a Model of Self leakage of Molecular Drag Pumps

  12. 一些人喜欢在工作间隙去度假,但是假期应该通过努力得到。

    Some people like to take a vacation between jobs , but a vacation should be earned .

  13. 本文对牵引分子泵抽气机理进行了深入分析,考虑了通道返流和工作间隙泄漏对泵抽气性能的影响。

    A further research on the pumping mechanism of molecular drag pump ( MDP ) has been made in this paper .

  14. 增压器高压腔体为承受周期性环向高应力的厚壁筒,在超高压下缸价内径与柱塞外径应变值不同,从而形成工作间隙。

    The high pressure cylinder of the booster is a thick wall barrel which can bear the high periodic circumferential stress .

  15. 利用静力学原理,提出该轴承更为合理的径向工作间隙检测方法。

    It brought forward a more reasonable examination method of radial work gap with principle of statics for this kind of bearing .

  16. 建立了磁粉离合器工作间隙电磁场与其转矩传递间关系,提出了通过电磁场分析得到磁粉离合器性能的方法。

    The relation between the electromagnetic field of the working gap and the torque transmission of the magnetic powder clutch was established .

  17. 尽管这些法规赋予员工们在长时间工作间隙休息的权利,但是否选择享用这样的权利还要看员工个人。

    These regulations give employees the right to take a break during a long work shift , but it 's up to them whether they do so or not .

  18. 本文主要论述由上位机和下位机构成的提升机盘形闸工作间隙实时检测系统构成和工作原理。

    This article introduced the real time monitor system for the disc-shaped brake of lift machine in coal mine , and the system is consist of main system and subsystem .

  19. 以常规自谱为特征建立了一套微型机故障诊断系统,并用该系统完成了对精密车床主轴轴承工作间隙的监测和识别;

    Using autospectrum as feature a micro-computer 's failure diagnosis system has been set up and monitoring and recognizing spindle bearing 's working clearance of precision lathe has been finished by the s-ystem .

  20. 并且对转速传感器不同工作间隙下触发信号相位角的测量,进行了高转速整车轮毂倒拖试验,验证了转速传感器高转速下的工作稳定性。

    Work And to speed sensor signal under different working clearance phase measurement , triggering high speed vehicle wheel trailing experimental results demonstrate that the speed of the high speed sensor working stability .

  21. 下位机采集的信号主要包括盘形闸的动态工作间隙、盘形闸贴闸油压、提升绞车的电压和电流以及提升电机的温度。

    The signals the sub-device collects include the disc-brake working clearance , the pressure pushing the dish-brake , the temperature of the lifting electrical machinery , lifting voltage and lifting current of the winch .

  22. 并在适当假设基础上,建立谷穗在静压载荷数学模型并进行相应的计算,结果与试验值误差小于4%,确定了相应的工作间隙。

    At appropriate assumption foundation , built up static pressure mathematics model and carry on the relevant calculation , error of experiment value is smaller than 4 % , made sure the homologous work clearance .

  23. 结果表明:在小于5μm的正常工作间隙下,转速对开启力、刚度和阻尼影响很大,而对泄漏量的影响很小;

    The results show when the film thickness is less than 5 μ m , the rotating speed has great effect on the opening force , stiffness and damping , while has little effect on leakage .

  24. 并在测定光栅信号质量及细分精度的基础上,推荐了25、50、100线/mm三种光栅的工作间隙区段,供实际工作的参考。

    Basing on the measurement of the grating signal quality and the subdivision accuracy , the working gap ranges of 25 , 50 , 100 lines / mm gratings are recommended as a reference for practical work .

  25. 工作间隙越小,密封具有越高的刚度、越低的泄漏量,但运行过程中的功耗较高、温升较大。

    When hydrodynamic mechanical seal works under the thinner film thickness ( < 3 μ m ) conditions , the higher power loss and higher temperature rise are inevitable , but the seal provides higher stiffness and lower leakage .

  26. 通过保护间隙与工作间隙放电特性的配合试验,证明加装保护间隙不仅可提高带电作业的安全性,而且能有效地减小塔头尺寸。

    Through the coordination test of discharge characteristics for protective gap and working gap , it is proved that adding protective gap can not only improve the safety for live line work and can reduce the tower size efficiently .

  27. 很多人喜欢在早晨起床后或工作间隙喝一两杯咖啡帮助提神,但如今,一位化学家发明出了能代替烘焙咖啡的快速提神制剂。

    Many people rely on a cup of coffee or two to wake them up in the morning or pick them up during the working day , but now a chemist has come up with a speedy alternative to crafting a cuppa .

  28. 根据五瓦对开式动静压液体滑动轴承的结构和功能特点,对轴承各要素的几何关系进行分析,阐明传统法检测径向工作间隙的工艺误差。

    According to the feature of structure and function of bisected five tiles dynamic and static pressure liquid sliding bearing , the article analyzed geometry relation of all elements of the bearing , illustrated the technology error of traditional examination of radial work gap .

  29. 许多办公室现在都有绿化区,可以在室内感受到大自然,还有养生房,会员可以在房间里冥想、做瑜伽,或在工作间隙做任何可以放松的活动。

    Many offices now include " green " areas that bring the feeling of nature indoors , and wellness rooms where members can meditate , practice yoga , or engage in any activity that lets them take a break from sitting at their desks . 3 .

  30. 提供了第一到第四道环的侧面间隙和工作开口间隙数据。

    The data on side clearance and open working clearance from the first to the fourth ring were provided .