现浇结构

第三章是对现浇结构工程外观质量缺陷的统计调查与分析。

In the third chapter , statistics analysis and investigation of defeats in cast-in-situ concrete structure .

施工缝是混凝土施工过程中的停歇位置，在现浇结构中，施工缝是不可避免的。

Construction joints are stopping places in the process of concrete construction and can 't be avoid in cast-in-situ concrete structure .

混凝土现浇结构裂缝的原因分析和处理

Causes analysis and treatment of the cracks in cast-in-site concrete structures

本文分析了叠合结构和整体现浇结构受力性能不同的根本原因在于叠合结构的二阶段制作、二阶段受力；

This paper analyzed and verified that the reason of composite structure behavior differing from general concrete structure is two-stage manufacture and load .

针对现浇结构楼板出现裂缝渗漏等质量缺陷，分析了现浇结构楼板裂缝渗漏的原因，从材料、施工、设计等方面进行了阐述，提出了具体的防治措施。

In connection with quality defect as split seepage on now-poured structural floorboard , it analyzes cause of split seepage on now-poured structural floorboard , illustrates material 、 construction & design , and puts forward concrete preventive measures .

本文以全现浇框架结构工程为主要研究对象，根据其三维CAD模型，按照编码原则对工程三维实体模型建立编码体系。

This article takes cast - in - site concrete building as the object , according to its 3D CAD model , found code system by code rule .

本文论述了某高校食堂全现浇框架结构未设置伸缩缝，而采用UEA补偿收缩混凝土的设计方法。

This paper discusses the design method of adopting UEA compensation contraction concrete , without installing expansion joint in the entire cast-in-place framework of a college canteen .

现浇框架结构钢筋工程施工质量调查

Investigation for construction quality of cast-in-place framework structure steel bar engineering

本设计采用钢筋混凝土现浇框架结构。

This scheme adopts the cast-in-place frame structure of reinforced concrete .

现浇框架结构梁、柱、板协同工作体系的有限元方法及其内力特征

Finite Element Method and Internal Forces of Cast-in-Place Girder-Slab-Column System

超低强度混凝土现浇框架结构的补强加固

Reinforcement of a cast-in-situ concrete frame structure of supper-low strength

现浇混凝土结构施工中一些问题的分析与防治

Analysis and protection measures on some problems of cast-in-place construction of concrete structure

现浇混凝土结构中临时留缝的分析

An Analysis of the Temporary Joint in Casting Concrete

现浇混凝土结构施工缝的设置与做法

Installation and Practice of Construction Joints of Cast-in-place Concrete

现浇混凝土结构工程的安全控制

The Safety Control of Cast-in-situ Concrete Structural Engineering

常见现浇混凝土结构外观质量缺陷原因与防治

On reasons and prevention for the quality shortage for the cast-in-situ concrete structural appearance

现浇砼结构粗钢筋连接新工艺

The New Tech of Jointing the Thick Reinfocing Bars in the Cast-in-place Concrete Structure

低温下现浇混凝土结构上吸式真空脱水工艺的研究

Research of vacuum dewatering technology for the surface of cast-in-situ concrete in the low temperature

对大面积现浇楼盖结构施工期温度场进行了仿真分析；

The temperature field of cast-in-place slab with large-area during the construction has been simulated .

对影响大面积现浇楼盖结构温度场和温度应力的因素进行了敏感性分析；

Sensibility of the influence of factors of temperature field and stress field has been analyzed .

现浇混凝土结构裂缝的分析及预防

Structural cracking in cast-in-site concrete

由于分散生产、专业化程度不高，钢筋工程长期以来一直是现浇混凝土结构施工中工作效率低、劳动强度大的一个工序。

Reinforcement work has always being a low efficiency working procedure in cast-in-place reinforced concrete engineering for it has not enough specialization .

从结构设计、混凝土材料、施工工艺等几方面总结大面积现浇楼盖结构裂缝控制的方法；

The methods to control crack of cast-in-place slab with large-area in several aspects , such as frame design concrete material and construction techniques are summed up .

该类型支撑具有施工方便、适用性广等特点，在现浇混凝土结构高大模板支架施工中被广泛使用，在我国建设施工中占有绝对的主流地位。

This type of support system has a simple and convenient construction process and an extensive applicability , it was used widely in the high-formwork construction of concrete structure .

模板是混凝土的成型模具，是现浇混凝土结构工程的重要组成部分。目前应用较多的圆柱模板有钢模板、木模板。

The template is a concrete molding , an important part of the cast-in-situ concrete structure . Currently the major cylindrical templates are steel formwork , and wood template .

模板技术。现浇混凝土结构模板拆除顺序的计算分析

Template technology is studied : This thesis studies template technology and design procedure . Calculation and Analysis of Formwork Dismantling Sequence for Cast - In - Place Concrete Construction

随着国家经济的飞速发展，工业与民用建筑工程规模日趋扩大，各种公共建筑和工业厂房越来越多的采用大柱网、大空间的结构形式，所以大尺度现浇楼盖结构得到了日益广泛的应用。

With rapid development of national economy , public buildings with its structure in the form of large-span and large-space , as well as industrial factories are getting more and more needed in cities .

但在试验中我们发现CL网架板混凝土单面预制存在很多不足，CL网架板混凝土双面现浇更有利于结构的整体性，使施工工序简化，质量控制点减少，大幅缩短工期。

But in experiments , it is found that there are defects in one-sided prefabrication of CL complex wallboard concrete , and two-sided cast is much better for the unity of the structure .

现浇钢筋混凝土结构是在建筑工程中应用最广泛的一种结构形式。

Cast-in-place reinforced concrete structure is applied widely in construction works .

某综合楼现浇坡屋盖结构工程事故分析与加固补强

Accident analysis on a cast-in-place pitched roof building and its reinforcement