电流探头

  • 网络Current Probe
电流探头电流探头
  1. 本文介绍了一种基于光/电转换技术的表面电流探头的设计方案。

    A surface current probe based on photoelectric conversion technique is presented .

  2. 利用内圆外方同轴传输线理论,提出弧面电流探头传输阻抗的校准方法。

    This paper presents a new method for measuring transfer impedance of arched surface current probe according as the theory of square coaxial transmission line with round center conductor .

  3. 不同磁芯材料对电流探头传输阻抗Zt的影响

    Influence of Magnetic Core Materials on Transfer Resistance Z_t in Current Probe

  4. 基于改进双电流探头法的EMI噪声源内阻抗测量

    EMI noise source impedance measurement based on modified dual-current-probe approach

  5. 为此,本文应用高频电压电流探头和光纤传输等技术,对安装SVC的变电站进行了现场传导干扰的测试。

    High-frequency voltage / current probes and optical fibre transmission techniques were used for on-site measurements at SVC-based substations .

  6. 同时在该测量系统标定时,利用脉冲信号源和示波器的电流探头进行测量,得到一组电流脉冲&示波器读数(I-V)校正数据,用这组数据绘制一条校正直线。

    And pulse signal generator and probe of oscilloscope are used to measure current pulse and I-V data through which a calibration curve is ploted .

  7. 一种基于光电转换技术的表面电流探头

    Surface Current Probe Based on Photo - Electric Conversion Technique

  8. 脉冲电流探头的时域标定研究

    Time domain calibration of pulsed current probe

  9. 电流探头校准的测量不确定度分析

    Uncertainty Analysis for Calibration of Current Probe

  10. 表面电流探头校准装置的设计及应用

    Calibration Device of Surface Current Probe

  11. 低频干扰电流探头中磁芯材料的选择对其检测性能的影响

    The Influence of selection of Magnetic Material on Its Experimental Performance in Low Frequency Interference Current Probe

  12. 电流探头注入替代辐射场的电磁敏感度自动测试技术

    Automatic test technology of electromagnetic Susceptibility ( EMS ) of Current Probe Injection instead of Radiated Field

  13. 在此基础上,利用注入电流探头对同轴电缆的屏蔽衰减进行了测试分析。

    Finally , the shielding attenuation of a coaxial cable is achieved by the S-matrix of an injection current probe .

  14. 采用高压、电流探头采集实时波形,对放电回路的电压、电流波形进行分析与研究,从而得出水中脉冲放电的工作特性。

    High voltage , current real-time waveform capture probe , the discharge circuit voltage , current waveform analysis and research to arrive at the work characteristics of pulsed discharge in water .

  15. 针对文中比值法存在的问题,结合双电流探头法原理,提出了一种新的阻抗测量方法&系统辨识法。

    Aiming at the problem of the ratio method cited in the paper and incorporating the principle of two-current-probe method , a novel impedance measurement method , system identification , is proposed .

  16. 针对电流探头的低频失真,采用系统辨识方法建立了测量系统的动态模型,并对探头输出信号的失真进行校正。

    A dynamic model of measurement system is established through system identification method according to low frequency distortion of the current probe . This method is also used to correct the distorted output signal of the probe .

  17. 提出了电流注入探头的两种电路模型:集中参元电路模型和分布式传输线模型。

    In this work , a lumped-parameter circuit model and transmission line model are discussed .

  18. 电流注入探头的仿真研究

    Simulated Research of Injection Probe

  19. 0.1TW脉冲功率源电流电压测量探头的设计与标定

    Design and calibration of measuring probes on 0.1 TW pulsed power source

  20. 对120kV的单次高压脉冲电流,不能直接采用示波器电流探头进行直接测量。

    KV single high-voltage current pulse can 't be measured by probe of oscilloscope .

  21. BMD-1型标准脉冲电流产生器是一种脉冲电流校准仪器,用于校准电流探头、电流探头放大器和其它电流测量仪器。

    The BMD-1 Model Standard Pulse Current Generator is a pulse current calibration instrument .

  22. 结果表明,流动电流SC可以对投药量变化进行调整,但流动电流的探头仍需改进;

    The results show that auto-dosing system of FRD could be improved by more sensitive probe of streaming current ( SC ) .