磨损试验

SiC颗粒增强的钢基复合材料的快速磨损试验研究

Rapid Wear Test of Steel Matrix PM Composite Reinforced With SiC Particles

W型磨损试验仪研制

Development of W Type of Wear Tester

EMC在摩擦磨损试验机研制中的影响及对策

Influence of Electromagnetic Compatibility in Developing Frictional Wear Test Machine and Its Countermeasures

用扫描电子显微镜（SEM）、划痕仪、显微硬度计、表面粗糙度仪、微磨损试验机等表征了钼涂层性能。

Molybdenum coating properties were studied by SEM , scratch tester , microhardness tester , surface roughness tester and micro-wear test machine .

用C／Cu复合材料与45钢在无润滑条件下进行磨损试验，统计分析试验数据.得出无润滑摩擦副材料磨损率服从标准正态分布。

On the basis of the wear test of C / Cu composite material we know that the wear rate of an unlubricated pair of friction obeys normal distribution .

本文利用MLS－23胶轮磨损试验机对超高分子量聚乙烯（UltraHighMolecularWeightPolyethylene）的磨粒磨损性能进行了研究。

In this paper , the rubber wheel abrasion rig of MLS 23 type was employed to study the abrasion of ultra high molecular weight polyethylene ( UHMWPE ) .

在销盘摩擦磨损试验机上建立了一套摩擦噪声测试系统，研究了具有相变特征的TRIP钢在单向连续滑动的摩擦试验过程中，摩擦噪声的强度的变化规律。

In the process of friction testing in which the TRIP steel with transformation characteristics is continuously sliding in unilateralism , variety rule of the friction noise intensity was studied .

并利用XRD、TEM、TG-DSC及摩擦磨损试验机对改性树脂及其摩擦材料的试件进行性能表征和测试。

The resin modified and friction material specimens are characterized and tested by means of XRD , TEM , TG-DSC and friction and Tear Testing Machine .

在磨损试验中，Al-Si合金+6%PbSn+低量MoS2有优于其他同类复合材料的耐磨性。Al/MoS2复合材料是一种很有潜力的自润滑耐磨材料。

Experiment shows that the wear resistance of Al-Si alloy + 6 % PbSn + MoS_2 is superior to that of other composites of a kind .

并用MM-200磨损试验机检测了所得复合镀层的耐磨性能。

Wear resistance was examined for the coatings by MM-200 wear tester .

采用盐雾腐蚀和磨损试验考核，结合SEM/EDS和XRD表征，分析了贫铀表面Al2O3/Al复合涂层的保护性能。

Protection of Al2O3 / Al multi-layer coatings for depleted uranium was investigated by using a combination of 5 % NaCI salt fog and abrasion test with SEM / EDS and XRD profiles .

利用环块磨损试验机在不同载荷下对热喷涂Al2O3-TiO2复合陶瓷涂层的乳化液润滑滑动磨损特性进行了研究。

The sliding wear behavior of thermal-sprayed Al2O3-TiO2 ceramic coating has been investigated with a ring-on-block wear tester under different loads in emulsion lubrication sliding .

在此基础上，设计了基于虚拟仪器技术的端面摩擦磨损试验机CAT系统，并对系统进行了分析。

Based on the above technology , we designed the end-face friction and wear testing machine CAT system based on the virtual instrumentation technology , at the same time , carried on analysis of the system .

利用扫描电镜（SEM）、盐雾腐蚀试验及对比磨损试验等分析手段研究了铝、镁合金微弧氧化陶瓷层的形成机理、镁合金微弧氧化陶瓷层耐蚀性及铝合金微弧氧化陶瓷层耐磨性。

SEM , salt spray tests and wearing tests were employed to characterize the growth mechanisms of micro-arc oxidation ceramic coatings , the corrosion resistance of magnesium alloys and wear-resistance of aluminum alloys with micro-arc oxidation .

用X射线衍射仪、扫描电镜、摩擦磨损试验等，研究了粉末冶金金属布及其钢表面改性技术在钢表面制备的WC－Ni系合金复合涂层的微观组织和性能。

The microstructure and properties of WC-Ni alloy composite coating manufactured by " Powdered Alloy Sheet " and corresponding steel surface hardening technology were studied by XRD , SEM , wear-resistance or abrasion resistance test etc.

利用自制销-盘式磨粒磨损试验机，测定聚四氟乙烯（PTFE）及其表面处理与未处理纳米氧化铝（Al2O3）填充聚四氟乙烯复合材料试件在干摩擦滑动条件下的磨粒磨损质量损失。

The wear loss of PTFE and composites of PTFE filled with surface modified and unmodified nano Al 2O 3 during dry wear was determined with a home-made pin-disk tester .

MM-200摩擦磨损试验机摩擦系数动态测试系统的实现

The implementation of dynamic testing friction coefficient system for MM-200 friction and wear tester

采用XRD与SEM分析技术、电化学阳极极化曲线测试和摩擦磨损试验等，系统地研究了FS-1化学镀Ni-P镀层的结构和性能。

The microstructure and properties of electroless plated Ni-P coating are systemically investigated by employing XRD , SEM , electrochemical anodic polarization curve measurement , and wear test .

进行了金相组织检查，显微硬度测定，X射线结构分析，磨损试验与渗氮层氧含量测定。

By microscopic examination , microhardness determination , X ray diffraction phases structures analyses , combined with the experimental works on wear resistance and determination of hydrogen content , the influence of the atmosphere on the nitrided layer was ascertained .

本文在石墨磨损试验的基础上，保守地估算了HTR-10在正常运行工况下石墨粉尘的产生量（大约为2.74kg/年）。

Based on the graphite wear experiments , we here estimated that the graphite generation under normal working condition is about 2.74kg/a .

在球盘式摩擦磨损试验机上，采用阶梯加载方式，测定了润滑条件下钢／钢滑动摩擦副的临界载荷－速度（P－V）图，分析了P－V图各区域的摩擦磨损特性。

This paper investigated the P-V digram for steel / steel rubbing pair under lubrication on a " ball-on-disc " testing machine , using the stepwise loading method , and analysed the behavior or friction and wear in various regions of the diagram .

SRV磨损试验表明，由于涂层中含有（Cr，Fe）7C3及合成的TiC硬质相，因此涂层具有良好的耐磨性能；

( Cr , Fe ) 7C 3 and Fe . The SRV wear test showed that RFS Cr Fe Ti C coatings have a good wear resistance .

采用有限元分析软件ANSYS对半球形微凸体接触应力和变形进行了仿真计算，并用销盘滑动磨损试验数据给予验证，证明了所建立的仿真模型是可行的。

Then , contact stress and deformation of a half sphere micro-convex was simulated and calculated by using finite element analysis software ( ANSYS ), and the testing model of pin-on-disc sliding wear was proofed through test data .

采用半固态挤压成形技术制备了Al-Si-Fe耐磨铝合金，分析了合金的微观组织，利用磨损试验研究了合金的耐磨性和磨损失效形式。

Microstructure and wear behavior of Al-Si-Fe alloy prepared by semi-solid squeezing casting have been analyzed .

利用冲击磨粒磨损试验，结合X射线衍射，SEM和Mossbauer谱等分析手段，研究了锰含量为4%～13%的奥氏体钢耐磨性和磨面组织结构。

The wear resistance and the microstructure of the worn surface of the steels containing 4 % ~ 13 % Mn were studied by means of abrasive wear test , XRD , SEM and Mossbauer spectroscopy .

利用HQ-1摩擦磨损试验机：考察了纳米TiO2的自修复性能，并探讨了其自修复机理。

HQ-1 friction and wear test machine was used to research self-repairing characteristics of surface modified nano-TiO_2 as additive in base oil .

摩擦磨损试验表明，该复合镀层与GCr15对磨其摩擦系数低至0.1，具有良好的自润滑效果，而且耐磨性也较Ni-P镀层好。

The wear test shows that Ni-P-PTFE coating has a low friction coefficient 0.1 , indicating good self-lubricant effect and better anti-wear than Ni-P coating .

MHK-500环块摩擦磨损试验机智能测控系统的研制

Study of Intelligent Testing System of MHK-500 Ring-Block Tribometer

通过摩擦磨损试验和扫描电镜分析等手段对NiPNanoAl2O3化学复合镀层的摩擦磨损性能进行了研究，分析了NiPNanoAl2O3复合镀层的磨损机理。

The friction and wear performances of Ni-P-Nano-Al_2O_3 electroless composite plating were studied by means of friction and wear test and SEM . The wear mechanism of Ni-P-Nano-Al_2O_3 electroless composite plating layer was also analyzed .

结合对单晶硅所进行的摩擦磨损试验，应用计算模型得出针尖的磨损率为1.7×10-10mm3/（N·m）；

As the results , the wear rate of the diamond tip in micro machining of a single crystal Si is calculated to be 1.7 × 10 - 10 mm 3 / ( N · m ), based on a theoretical model combined with the experimental results .