粘合强度

研究了BN含量和尺寸对粘合强度的影响。

Investigate the effect of BN content and size on the adhesive strength .

实验发现，PVDF分子量小有利于离子迁移，但粘合强度不够；

The experimental results show that the PVDF with low molecular weight is favorable to ion transfer but the adhesive strength is not sufficient , while that with high molecular weight is not favorable to ion transfer due to the small inner free volume .

随着BN含量的增加和尺寸的增大，水玻璃粘合强度逐渐降低，而热导率的变化与之相反。

With the increase of BN content and size , the bonding strength of water glass decreases , while the thermal conductivity changes in contrast .

以镁盐晶须增强聚丙烯（PP）复合材料为研究对象，添加马来酸酐接枝聚丙烯（PPgMAH）1与PPgMAH2界面改性剂来改善两者界面粘合强度及提高复合材料的力学性能；

It was focused on the polypropylene reinforced with whisker . By adding different interfacial modifiers : PP-g-MAH 1 and PP-g-MAH 2 , the interface adhesion and mechanical properties of the composites were improved .

结果表明，绢云母粉活化后对胶料的老化性能、疲劳性能、半成品粘合强度、H抽出力等性能有所改善，但焦烧时间和正硫化时间缩短；

The results showed that the aging properties and fatigue properties of compounds and the adhesion strength and H pull out force of semi products improved , and the scorch time and optimum cure time reduced by adding activated silk mica powder ;

在EVA中混入EPDM可使发泡材料的拉伸强度、撕裂强度和粘合强度提高，而收缩率和压缩永久变形降低；

It was found that the tensile strength , tear strength and adhesion strength of the foam increased , and the shrinkage and compression set of the foam decreased by blending EVA with EPDM or IIR ;

用低熔点聚酯对热塑性聚氨酯进行改性，并对所制备的复合薄膜进行热粘合强度、DSC、透湿性、耐静水压以及力学等各项性能测试。

Films for lamination were prepared via a melt blending of thermoplastic polyurethane ( TPU ) and polyester with low melt point , and their moisture permeability , thermal bonding properties , resistance to hydrostatic pressure and mechanical properties were tested .

结果表明，辐射接枝可使复合材料层间剪切强度增大20%左右，使扭辫分析试样的Tg从416.8K增大到424.3K，复合材料界面粘合强度提高。

The results show that the interlaminar shear strength of composite are increased by 20 % after radiation grafting . The Tg of specimen for torsional braid analysis is increased from 416.8K to 424.3K and the interfacial adhesion strength is improved after radiation .

选用C-3化学处理剂及M型、EJ型粘合剂，FRP-PVC的粘合强度达10MPa，且化学处理、粘合、玻璃钢成型及固化一步完成。

The adhesive strength can reach to 10 MPa for fiber reinforced plastics composite pipe when C-3 treating agent and M-type or EJ-type binder were used . All the procedures including chemical treatment , adhesion , fabrication and Curing are performed in one step .

分层出现与否取决于界面粘合强度和应力的竞争，因而由封装构型及材料特性决定。

Delamination initiation depends on the competition between interfacial stress and adhesion .

玉米淀粉粘合剂的制备、性能及粘合强度的研究

Manufacturing and property of corn starch binder and Study on binding strength

GB/T7761-1987橡胶与刚性材料粘合强度的测定圆锥形件法

Rubber & Determination of adhesion to rigid materials using conical shaped parts

环氧树脂的两种肤类硬化剂对粘合强度的影响

The Effects of Curing Agents on the Adhesive Strength of Epoxy Resin

高性能大尺寸永磁体粘合强度的测定

Determination of adhesive strength for big SIZE-HIGH energy agglutinated magnets

GB/T14905-1994橡胶和塑料软管各层间粘合强度测定

Rubber and plastics hose & Determination of adhesion between components

在粘接1个小时以后，达到60%的粘合强度。

The bonding strength is60 % after one hour .

浅谈纸原料和粘接剂对瓦楞纸板粘合强度的影响

Effects of Paper Material & Adhsive on the stickiness of Corrugated Paper Board

GB/T532-1997硫化橡胶或热塑性橡胶与织物粘合强度的测定

" Rubber , vulcanized or thermoplastic & Determination of adhesion to textile fabric "

GB/T1742-1979胶液粘合强度测定法

Method of test for adhesive strength of sizes

榴弹隐身涂层粘合强度分析

Adhesion Strength Analyzing of Stealth Bullet RAM

GB/T6759-1986输送带的层间粘合强度测定方法

Conveyor belts & Determination of ply adhesion

三种胶体材料及其复合物作为骨粘合剂的粘合强度比较

Comparative study on adhesive strength of three colloid materials and their complexes as bone adhesives

GB/T12833-1991橡胶和塑料撕裂强度及粘合强度多峰曲线的分析方法

Rubber and plastics-Analysis of multi-peak traces obtained in determinations of tear strength and adhesion strength

GB/T17044-1997钢丝绳芯输送带覆盖层与带芯层粘合强度试验方法

Steel cord conveyor belts & Adhesion strength test of the cover to the core layer

金属材料表面能的测算及其对粘合强度的影响

Determination of the Surface Energy of Some Metal Materials and Its Effects on the Adhesive Strength

GB/T5755-1986钢丝绳芯输送带钢丝绳粘合强度的测定

Steel cord conveyor belts-Cable-to-coating bond test

该胶粘剂以改性溴化丁基橡胶为主体材料，具有很高的粘合强度，优异的耐水性和耐候性，该胶粘剂的储存稳定性也令人满意。

The adhesive provides high bonding strength , excellent water-and weather resistance , satisfying shelf time .

绳、带子、编绳的断裂强力和断裂伸长率的测定法GB/T5755-1986钢丝绳芯输送带钢丝绳粘合强度的测定

Testing method for breaking strength and elongation of webbing , tape and braided Steel cord conveyor belts-Cable-to-coating bond test

经过处理后的电解铜箔耐蚀性、耐热性和粘合强度等性能指标均有明显提高。

After the plating , corrosion resistance , heat resistance and binding strength of electrolyte copper foil were improved .

GB/T1742-1979胶液粘合强度测定法注聚液在线粘度检测与控制系统设计

Method of test for adhesive strength of sizes Design of On-Line Measurement and Controlment for Viscosity of Polymer Liquid