铜套

AV铜套（面板）脆裂原因分析及解决方案

Results for embrittlement of AV copper bushing ( panel ) and its settlement

冷态下局部过小间隙还会造成热膨胀状态下无间隙而使铜套受损。

In cold state , excessive small gap in partial zone can cause free-clearance under thermal expansion effect and cause the copper bushing damaged .

Cu-Ti-Sn-Cr结晶器铜套的研制

Development of Cu-Ti-Sn-Cr Crystallizer Copper Sleeve

水平连铸用结晶器内壁铜套的研制

Development of inner copper bush of crystallizer for horizontal continuous casting

薄壁铜套的车削与夹具设计

Turning of The Thin-Wall Copper Sleeve and Design of Fixtures

艉轴铜套局部换新修理方法探讨

Probe to Replacement and Repair of Stern Shaft Liner Copper Sleeve Partially

大型铜套类铸件的金属型铸造工艺

Study on the Casting Process of Metal Mold for Large-scale Copper Sleeve Castings

热熔断器的外圆上铆接有铜套。

The outer circle of the thermal fuse is riveted with a copper sleeve .

短铜套结晶器水平连铸的研究开发

Research & development of horizontal continuous casting with the mould of short copper jacket

柴油机气缸盖喷油器铜套压装方法

The Method for Assembling on Copper Sleeve of the Cylinder Head in Diesel Engine

铅青铜特大铜套的研制

Development of Heavy Lead Bronze Jacket

从粗车后收缩量的判定，机床刀架角度的重新调整两方面出发，介绍薄壁铜套精车尺寸的确定。

According to shrinkage , angles of lathe saddle are adjusted to ensure precision of thin-wall case .

应用正交试验法解决高压泵十字头铜套过热抱死问题

Solution for Overheat Lock Breaking of Crosshead Copper Sleeve in High Pressure Pump by Orthogonal Test Method

铜套的质量高低直接影响炼钢的效率、效益及劳动强度。

The quality of copper alloy mould directly affects the steel-making efficiency , effectiveness and labor intensity .

是用拳头打是拳打脚踢用我的指节铜套

Oh , of oh , a punching , It 's kicking and punching.with my knuckle dusters .

减速顶衬套磨耗分析及钢背铜套在减速顶产品中的应用简介

Analysis on Wearing of Retarder Bush and Brief Introduction on Application of Steel Backing Copper Bush in Retarder Products

本文着重介绍了薄壁铜套的车削工艺及夹具结构设计。

This paper made chiefly an introduction on turning process of the thin wall copper sleeve and design of fixture structure .

铜套包括同轴固定于支架内的上铜套和下铜套；

The copper sleeve comprises a upper copper sleeve and a lower copper sleeve fixed inside the supporter by the coaxial ;

广泛用于零部件的压型、压弯、冲孔、压印、轴承压装、铜套压装及轴类零件的校正、压装、翻边铆合等。

Products widely used in parts of the press forming , stretching , bending , punching , stamping , shaft alignment and press-fit and so on .

试验结果表明，砂型铸造铜套性能较差，而真空吸铸铜套性能较好，可以替代卷制铜套。

Result of testing shows that proPerty of sand casting bushing is unsatisfactory and that of vacuum casting bushing is better , which can be used to replace the pressed bushing .

设计和制造了1台双金属双结晶器连续铸造试验机，其特征是：①结晶器为水冷铜套内衬石墨套；

We have developed a continuous casting machine with dual crystallizer for compund bimetal . The machine is characterized as follow : 1 , graphite sleeve set in water cooling copper sleeve ;

文章介绍了艉轴填料函密封的基本原理，分析了漏水的原因，提出了艉轴铜套分段红装修理的具体操作方法。

This paper presents the principle of stern stuffing seal , analyses the reason of water-leaking and provides in detail the technique of fitting operation on divided bronze liner of stern shaft .

研究结果表明：（1）造成铜套失效的主要原因为内部出现划痕、掉块及热裂纹。

The results are shown as follows : ( 1 ) The main reason for the failure of copper alloy mould is that it occurs within the scratch , the peeling and thermal crack .

推导了考虑水冷铜套和电极之间空气隙影响的等效对流换热系数以及通电时的径向和轴向电磁力方程。

Equivalent convective heat transfer coefficient with considering the air clearance between the water-cooling copper cover and the bottom electrode was calculated and the electromagnetic force equations of the bottom electrode in the axial and radial direction were deduced when electrification started .

就是，打拳的时候比别人出拳要出那么一点，一套指节铜套，手套上的条纹，一枚警徽，手中的石头，或者你口袋里的钞票。

Yeah , a little extra reach on a punch , a set of brass knuckles , a stripe on the sleeve , a badge that says cop on it , a rock in your hand , or a bankroll in your pocket .

无氧铜深孔套料加工工艺的试验研究

Experimental Study on Deep-hole Trepanning Technology for Oxygen-free Copper

防波套是用于防止电波干扰或起保护作用的屏蔽铜编织套。

The wave-proof sleeve is a kind of shielded copper braiding sleeve for preventing the interference of electric wave or playing the effect of protection .

磷酸铜无机胶套接强度的探讨

The Sheath Interlink Strength Research for Copper Phosphate Adhesive

磷酸氧化铜无机胶套接扭剪强度研究

Investigation on Torsional Sheath Strength of Dowel Joint of Copper Phosphate A Study on Modified Cupric Oxide-Phosphoric Acid Inorganic Adhesive

水平连铸是现代各大钢（管）厂生产各类型钢的主要方法，结晶器铜合金内套是水平连铸设备中最为关键的易耗部件。

Horizontal continuous casting is the main method of billet produced for the modern big steel ( tube ) factories as well as copper alloy mould is the most critical consumable parts of horizontal continuous casting equipment .