铝板

PS版对铝板基的质量要求

Quality needs of aluminium sheet used for presensitized plate

介绍了我国铝板带箔的加工现状、存在的问题、市场需求及国外的发展，分析了加入WTO后我国铝板带箔加工业面临的机遇和挑战。

The paper deals with the present status , existing problems and market demand of aluminium sheet , strip and foil in china and development tread abroad and analyzes the opportunities and challenges brought forth to the china 's aluminium sheet foil processing industry by the entry to WTO .

大多数太阳能热水器使用大片的涂成黑色的铝板或合金板来吸收太阳的热量。

Most solar heating systems use large aluminum or alloy sheets , painted black to absorb the sun 's heat .

用KH计算法编制铝板带压下规程

Aluminium Sheet Strip Rolling Schedule Worked out by K_ H Method

CAD技术在矩形铝板幕墙排样中的应用

Application of CAD in the Layout of the Rectangle Aluminium Coating Wall Plate

受拉铝板对连续波CO2激光的热机械响应

Thermomechanical response of Al plates under tension to CW co_2 laser radiation

PS版铝板基的制备工艺及性能研究

Study on Preparation Process and Properties of Aluminium Substrate PS Plate

富铝莫来石相的XRD定量铝板轧制织构的定量研究

Quantitative Investigation of Rolling Texture in Aluminium Plate

有限元与MonteCarlo方法耦合的冷轧纯铝板再结晶模拟

Coupling of FEM with Monte Carlo for simulating recrystallization in cold rolling pure aluminum sheet

进口与国产PS版用铝板组织与性能的对比

Comparison of Properties and Microstructure between Imported and Domestic Aluminium Substrate of PS Plate

国内外PS版用铝板基综合测试与分析

Comprehensive Testing and Analysis of Aluminium Substrate of PS Plate from Home and Abroad

Lamb波在薄铝板无损评价中的模态识别与应用

Mode Identification and Application for Nondestructive Evaluation of Thin Aluminum Sheet by Lamb Waves

铝板热轧机的液压AGC控制

Hydraulic AGC control of hot rolled aluminum sheet mill

扫描电子显微镜在PS版铝板基砂目形貌观察中的应用

Application of scanning electron microscope in the observation of grain profile on aluminium substrate of PS plate

基于Fuzzy-PID的超薄快速铝板铸轧机前箱液位控制

Liquid Level Control of Aluminum Strip Ultra-Thin High-Speed Casting Headbox Based on Fuzzy-PID

进行了含不同方向裂纹铝板试件的检测实验，生成了U检测模式和T检测模式的修正C扫描图像。

Detect the Aluminum specimen with cracks in different directions , generate the eddy current array modified C scan images in U testing mode and T testing mode .

利用弹塑性大变形更新的Lagrange有限元法对于复合成形中铝板成形过程进行了数值模拟。

The updated elastic-plastic Lagrange finite element formulation was used to simulate the forming process of the aluminum sheet .

MIG焊在大厚度铝板焊接上的应用

Application of MIG on heavy plate aluminum construction

线型切割索侵彻硬铝板的实验研究及数值模拟仿真金属板料幂指型硬化模型应变强化系数K值研究

Experimental Research and Numerical Simulation of Linetype Shaped Charge Jet s Penetration into Alloyed Aluminum Plates ; Research on strength coefficient in power hardening model of sheet metal

冷轧复合工艺制备超轻Mg-Li合金复铝板

Preparation of Mg-Li alloy / Al composite plate by cold-rolling bonding process

利用所测量的铝板织构和Sachs以及反应应力模型对铝板不同方向塑性应变比进行了模拟计算。

The r values in different sheet directions were calculated based on Sachs model and Reaction stress model in consideration of the measured textures .

分析表明，Mg含量从0.001%提高到0.10%时，Mg更多地富集于铝板表面，形成微小的易腐蚀的含Mg复合氧化物颗粒，促进腐蚀，进而提高板基的腐蚀速率；

When the content of Mg increased from 0.001 % to 0.10 % , Mg was enriched more to the surface of aluminum plate and formed fine compound-oxide grains , resulting in accelerated corrosion .

研究了电解铝液直接铸轧生产PS版铝板基的主要缺陷，并分析了缺陷产生的原因。

The main defects of aluminum substrate for PS plate produced by direct cast-rolling of electrolysis aluminum liquid were discussed , and the reason for the defects was analyzed .

L2Y2铝板3维曲面的无模成形试验研究

The Study of Experiment of L_2Y_2 aluminium Plate Three-dimension Curve Multi-point-Forming

本文扩展了实验的演示方式，分别在平行铝板作用下、单铝板作用下、金属尖端作用下和X射线作用下观察富兰克林轮的转动。

That is , the running of Franklin wheel is studied as the parallel aluminum plates , one single aluminum plate , the top of metal and X ray are chosen as the experiment 's samples .

对热轧铝板的织构进行了X射线反射法剥层测量和X射线透射法直接测量。透射法测量时需要对极图数据作绕轧向转90°的坐标转换。

The texture of hot rolled aluminum plate was measured on decorticated sample by X-ray reflection technique as well as by X-ray transmission technique , in which a 90 ° coordinate rotation around rolling direction is requested .

利用CFD商用软件Flow-3d对铝板坯半连续铸造充型过程中流场与温度场耦合作用下的凝固过程进行了数值模拟。

The numerical simulation of solidification processes were done under flow field and temperature field by using CFD commercial code Flow-3d .

研究结果表明：当PP中不含MPP时，界面粘接强度低，拉伸剪切时表现为铝板/聚丙烯粘接界面的破坏；

The results show that the adhesion strength is low and the adhesion bonded aluminum sheet / polypropylene / aluminum sheet fractures at the interface when there is no MPP in PP.

用扫描电子显微镜（SEM）对PS版铝板基上的砂目形貌进行了观察分析，比较了不同砂目形貌对PS版性能的影响。

The scanning electron microscope ( SEM ) was used for observing and analyzing grain profiles on aluminium substrate of PS plate . Effects of different grain profiles on the performance of PS plates were compared .

得到材料内部的瞬态温度场以及由温度梯度引起的瞬态应力场，该应力场以超声Lamb波的形式在铝板材料中传播。

Then , the transient stressfield induced by temperature grads was obtained in the plate , and it is found that the transient stressfield propagates in the form of Lamb waves in the aluminum plate .