不锈钢管

通过对现有设备的改造和组合，实现了适合直径20mm、壁厚0.8mm不锈钢管的微束等离子弧焊接过程，取得了满意的焊接质量和外观成形。

20 mm in diameter and 0.8 mm in wall thickness stainless steel pipe was pulse micro-plasma arc welded using the reformed and combined equipment , which can achieve satisfactory weld - ing quality and appearance formation .

使用LGK空气等离子切割机和磁力管道切割机的组合加上一定的辅助手段，改善了不锈钢管及合金钢管的坡口加工效果，使加工出来的坡口像碳钢管一样平整，更加容易打磨组焊。

Combining LGK air plasma cutter with magnetic force pipe cutter and adding assistant means , groove making of stainless steel pipe or alloy steel pipe is improved . The processed grooves are trim for easy burnishing and assembling .

不锈钢管比铜管不易纠结，但不经酸性处理焊接较困难。

The stainless tubing is less likely to kink than copper , but it is harder to solder without an acid treatment .

提高不锈钢管内衬PTFE管施工效率的探讨

Discussion on Improving Construction Efficiency of the PTFE inside Stainless Steel Piping

紫铜换热管与不锈钢管板接头的TIG焊

TIG welding for austenitic stainless steel tube plate and copper pipe

双相不锈钢管板手工TIG填丝焊接工艺的研究

Welding Process of Duplex Stainless Steel Tube-sheet with Manual TIG Filler Wire

推导了裸FBG以及不锈钢管封装的FBG温度传感器的温度敏感因素并进行了实验验证。

The temperature sensitive factors of the sensors were derived analytically and are verified by experiments .

设计了一种基于不锈钢管的小尺寸光纤光栅（FBG）温度传感器。

A small-size package method , stainless steel tube package based method for fiber Bragg grating temperature sensor , was designed .

用国产BTA深孔钻头加工奥氏体不锈钢管板深孔

Domestic BTA Deep Hole Drills Machining Austenitic Stainless Steel Tube

不锈钢管OPGW设计规则

Design rule for stainless steel tube OPGW

结果表明TP304H不锈钢管中的Cu含量偏高。

It indicates that the copper content of the stainless steel tube is high .

利用炻器管负载TiO2催化降解亚甲基蓝（MB）的速率常数是不锈钢管和玻璃管的2倍；

Degradation rate constant of methylene blue with TiO_2 membrane on ceramic is twice of that with membranes on glass and stainless steel .

所用色谱柱为不锈钢管，内填6080目的6201担体及SE30硅橡胶固定液，柱箱采用程序升温。

The GC column consists of a stainless steel tubing , packed with SE-30 silicone gum rubber on 60-to 80-mesh 6201 support and is temperature programmed .

生产工艺对00Cr17Ni14Mo2（316L）不锈钢管质量的影响

Effect of Procedure Factor on Quality of 316L Stainless Steel Tube

结果表明：细不锈钢管封装的FBG温度传感器的中心波长在-60℃时发生了突变，急剧下降；

From the experimental results , it is shown that the center wavelength of FBG temperature sensor with thin stainless steel tube package falls sharply at-60 ℃;

某热交换器是由400余根φ10mm×1mm呈S形的不锈钢管组成。

The heat exchanger was installed with 400 stainless steel S tubes of 10 mmx 1 mm .

细直径（≤φmm）不锈钢管平口环对接接头，是技术难度较大的焊接接头，也是工业应用越来越多的一种细径管平滑连接方法。

The circumferential square butt joint of small-diameter (≤φ 3mm ) stainless steel tubes is difficult to be welded in technique and that is , a smooth joint process of small-diameter tubes . which is widely applied in industry .

该文介绍了铝管式OPGW的抗雷性能，并与不锈钢管式OPGW做了比较。

This paper presents the performance of lightning resistance of aluminum tube type OPGW , and the result of comparing with stainless steel tube OPGW .

汽车排气管使用的ERW不锈钢管，要求具有较高的耐高温、抗氧化性能，而且还要具备良好的二次加工性。

S : The ERW stainless motor vent-pipe not only requires high anti-temperature and ant-oxidation property , but also requires the best reprocess ability .

复合不锈钢管结构及铝包不锈钢结构光单元可以从结构上杜绝OPGW光单元的径向渗水。

The application of the optical unit with the structure of compound stainless tube and Al-clad stainless will put an end to the horizontal fluid penetration structurally .

STR-1新型不锈钢管冷轧润滑剂

STR-1 new lubricant for cold-rolling process of stainless steel tubes

通有含溴离子氮气的304L不锈钢管，经一段时期的使用后产生了严重点蚀。

Pitting corrosion was found on the inner surface of 304L stainless steel pipes , which was exposed to nitrogen gas containing bromine ions .

介绍一种新型的架空地线复合光缆（OPGW），其光纤单元是一种具有PBT（聚对苯二甲酸丁二醇酯）内衬管粘合不锈钢管的松套型结构。

The paper has introduced a new kind of overhead compound optical ground wire ( OPGW ), whose optical unit is kind of loose sleeve structure with stainless steel pipe bond with PBT lining tube .

叙述了在Φ250mm狄塞尔穿孔机上穿轧Φ310mm不锈钢管坯的工艺过程，并对出现的问题进行了分析。

Described in the article are the technological process of rolling Φ 310mm stainless steel shells with the Φ 250mm Diescher piercing mill , and analysis of problems concerning the process .

若中水氯离子含量不高，可有条件地采用TP316不锈钢管或BFe30-1-1管；

The TP 316 stainless steel tube or the BFe 30-1-1 tube can conditionally be used , if the chlorine ion content in reclaimed water to be not high ;

在无菌环境下点样于内径为6mm的不锈钢管内，观察含菌琼脂平皿内抑菌圈大小。

In the bacteria - free environment , we dropped the above four solutions as a sample into the four different stainless steel tubes with an inner diameter of 6 mm and observed the size of the inhibitory rings in the bacterial agar plane pools .

由于发电设备向高温、高压和大容量化发展，近年来国外一直致力于研制9～13Cr高铬钢管取代锅炉现用的18&8系不锈钢管。

Since the power generating equipments tend to high temperature , high pressure and large capacity , the foreign countries have been developing 9 ~ 13Cr steel pipes with high Cr content instead of the current 18 ~ 8 stainless steel boiler pipes .

介绍了用于不锈钢管增强的SY-ZQ增强带的力学性能及加速老化性能、胶接工艺和典型件的疲劳性能。

In this paper , mechanical and accelerated aging properties of SY-ZQ adhesive bonding reinforced strap which is used to strengthen the welding line of stainless steel tube , bonding process and fatigue properties of representative pieces were introduced .

对我国建筑常用金属材料生命周期能耗进行计算分析，结果表明型钢、钢筋、不锈钢管、铜管、铝型材的综合能耗值分别为1.17tce/t、1.47tce/t、2.3tce/t、2.85tce/t、4.43tce/t。

Comes to the conclusion that the material energy consumption for profiled steel bar , reinforcing steel bar , stainless steel pipe , copper pipe and profiled aluminum bar are respectively about 1.17tce / t , 1.47tce / t , 2.3tce / t , 2.85tce/t and 4.43tce/t .

细径薄壁不锈钢管的氩弧焊接工艺

Technology of TIG in small drive thin wall stainless steel tube