冲击性能

EVA改性PVC体系的冲击性能研究

A study of impact properties of EVA modified PVC

滑石粉填充PP材料中颗粒分布分形特征及其与冲击性能的关系

The particle fractal distribution in pp / talc materials and its relation with impact properties

Al2O3陶瓷涂层抗高温热冲击性能的研究

Study on High Temperature Thermal Shock Resistance of Al_2O_3 Ceramic Coating

热空气老化和热水老化对PC冲击性能的影响

Effect of hot air aging and hot water aging on impact properties of polycarbonate

对Ti（C，N）基金属陶瓷的热冲击性能进行了研究。

The thermal shock properties of Ti ( C , N ) based cermets have been studied .

ABS/改性PP共混物形态与冲击性能

The morphology and impact property of abs / modified PP blending material

PVC能显著提高ABS/PVC体系的阻燃性能和冲击性能。

PVC could increase FR and impact property of ABS / brucite .

研究并制备出具有较好冲击性能的PVC/ACR共混合金。

It studied and prepared the PVC / ACR alloys which possesses good impact strength .

随着C含量提高，焊接粗晶区中的晶粒粗化被抑制，因此，使得冲击性能和疲劳强度被明显提高。

As carbon content increasing , the grain coarsening of CGHAZ is inhibited , thus , the impact toughness and fatigue strength are significantly improved .

研究了ABS用量变化对改性硬质聚氯乙烯体系冲击性能的影响。

Effects of dosages of ABS on the impact strength of rigid PVC were studied .

HDPE／橡胶／CaCO3复合材料抗冲击性能的研究

The Study of Impact Resistance of HDPE / Rubber / CaCO_3Composite Materials

等离子喷涂ZrO2热障涂层的热冲击性能

Thermal Shock Resistance of Plasma-sprayed ZrO_2 Thermal Barrier Coatings

经γ射线辐照的LLDPE与氢氧化铝体系冲击性能的研究

A Study on Impact Properties of γ - Ray Irradiated LLDPE Filled with Alumina Trihydrate

EPDM粘度对PP/EPDM共混物断口形态和冲击性能的影响

Effects of Mooney viscosity of EPDM on morphology of fractured surface and impact property of pp / epdm blends

正火工艺对20g钢板时效冲击性能的影响

The Effect of Normalizing Process on Ageing Impact Property of 20g Steel Plate

EPR的分子序列结构对聚合物抗冲击性能起主要作用。

The molecular sequential structure of EPR exerts a significant effect on the impact property of the polymer .

CPVC加工性能和冲击性能的改进

Improvements on processing properties and impact properties of CPVC

PA1010/聚酯型TPU共混体系的冲击性能和其断裂形貌研究

Study on the Impact Properties and Fracture Morphology of PA1010 / ester-based TPU Blends

PP/纳米CaCO3复合材料的抗冲击性能

Impact property of PP / nano-CaCO_3 composites

采用新方法生产的废轮胎胶粉（粒径120～180μm）作为增韧材料填充到聚氯乙烯（PVC）中，以提高PVC材料的抗冲击性能。

The waste tire rubber fine powder prepared by new method was used to produce toughening PVC composite , and the impact property of the composite was improved .

以稀土强化Al2O3/Ti（C，N）陶瓷材料为基础，进行了基于抗冲击性能、抗热震性能和耐磨性能的组分设计。

Based on the rare earth reinforced Al2O3 / Ti ( C , N ) ceramic material , compositional designs aiming at the impact resistance , thermal shock resistance and wear resistance have been carried out .

当填充量为30%，复合硅灰石粉体填加的PP复合材料的冲击性能要高出硅灰石矿物粉体填加的PP复合材料的30%以上。

When the filling ratio is 30 % , the impact strength of PP filled by composite wollastonite was greater than PP filled by wollastonite more than 30 % .

研究结果表明，随着CPE和纳米Mg（OH）2含量的增加，材料的抗冲击性能和阻燃性能得到改善。

The results show that the impact resistance and flame-resistance of the composite material is improved as the content of CPE and nano-Mg ( OH ) 2 is increased .

热处理对Ni-Al涂层耐热冲击性能的影响

Effect of Heat Treatment on Resistance to Thermal Shock of Ni & Al Coating

实验结果表明：ABS材料的微观相形态、分布及界面结合情况对其性能尤其是冲击性能有着重要影响。

The results showed that the performances , especially the impact strength , were strongly affected by the microcosmic structure , the phase distribution and the combination of interface .

PVC-U门、窗框异型材低温落锺冲击性能影响因素及控制措施浅析

Humble Analysis of Causation and Controlling Methods to Falling Impact Performance of PVC-U Plastic Profile at Low Temperature

结果表明在MDF水泥基体中加入少量尼龙纤维可以有效地提高材料的抗冲击性能。

The results indicate that small volume fraction of nylon fiber in MDF cement matrix could improve impact performance of the composites .

但是长期以来，山于金属Ni不能完全润湿TiC和TiN，致使合金韧性不足，抗冲击性能较差，限制了其应用。

However , in a long time , the toughness and resistance to impact are not satisfactory because metal Ni can 't wet TiC and TiN completely , its applications are limited .

在室温下测量了2种合金的拉伸性能和Izod冲击性能。

The tensile and Izod impact properties of the alloys were measured at room temperature .

结果表明：在低用量条件下，随MBS树脂含量增加，MBS/PVC抗冲击性能有所提高，光学性能略有下降。

Generally , when the content of MBS resin is low , the impact resistance increases with increase in MBS content , with slight decrease in transparency .