水淬

该技术的关键有：还原焙烧、水淬、酸浸。

The key technology consists of reduction roasting , shrend and acid leaching .

水淬铜渣是铜冶炼过程中产生的一种工业废渣，颗粒略粗于普通砂。

Shrend copper ash is a kind of industrial waste out of smelting process of copper , with its grain slightly bigger than normal sand .

用钛基组合钎料对Ti－10%Zr合金进行电阻钎焊，断电后水淬或气冷处理。

Ti-10 % Zr alloy was resistance-brazed with Ti based filler metal by subjecting to water or gas cooling .

等离子喷涂ZrO2涂层的火焰喷烧和水淬热冲击

Thermal Shock with Flame Jet and Water Quenching of Plasma-sprayed ZrO_2 Coatings

1200℃水淬样品由单一的B2相组成。

The microstructure of the 1200 ℃ quenched sample consists of single B2 phase .

铬青铜的最佳固溶工艺为：1000℃保温1h后水淬；

The best solution process of chromium bronze is at 1000 ℃ for an hour followed by water quenching .

当水淬终止温度略低于Ms点时，钢的自回火程度最大，呈现出韧性峰值；

When the interrupted quenching temperature is just below Ms , self tempering of martensite could reach its highest level and then a toughness peak may occur at this temperature .

研究了水淬矿渣的特性，检测了不同细度、掺量的矿渣微粉与P·Ⅰ熟料或P·O配制的P·S或复合硅酸盐水泥的性质。

The paper introduces the research on the properties of water quenching slag . Testings are made on the features of different fineness and different addition of super-fine slag to the P.S or compound Portland cement with P · I clinker or P.O.

采用直接水淬法成功制备直径5mm球状Zr65Al7.5Cu17.5Ni10大块非晶态合金。

Bulk amorphous Zr 65 Al 7.5 Cu 17.5 Ni 10 alloy was produced by a direct water-quenching method .

采用水淬法制备了Zr-Ti-Cu-Ni-Be-Co块状非晶合金（BMGs）。

Zr-Ti-Cu-Ni-Be-Co bulk metallic glass were prepared by water quenching method .

研究了稀土、超量硅、AlTiB、稀土添加剂以及风淬与水淬对6063铝合金强度的影响，并从理论上阐明了材料的内部结构变化。

The factors of thulium , excessive silicon , Al Ti B , thulium additive and quench with wind and with water , which influence the intension of 6063 aluminum alloy , were investigated . The change of the inner structure were illustrated in theory .

碱性氧化物含量低、SiO2含量高的酸性镍冶炼水淬渣，欲获得较高的活性，须磨到足够大的比表面积和选用适宜的活化剂。

Ground to fine enough so with large specific surface and using adequate activator are the necessary measures to gain high reactivity for pulverized slag of nickel smelting with low caustic oxide content and high SiO_2 .

微量Ce，La的加入，提高了经水淬后80℃温轧的Zn-22%Al合金的阻尼性能，减缓了经150℃时效后阻尼性能的降低。

Traces of Ce and La can improve the damping capacity of water quenched and warm rolled Zn 22 % Al , and decrease the reduction of the damping capacity of Zn 22 % Al during ageing at 150 ℃ .

研究了等离子喷涂ZrO2涂层在水淬和火焰喷烧两种条件下的热冲击性能，采用ANSYS软件对两种条件下涂层的热冲击性能进行了有限元计算。

The thermal shock of plasma-spraying ZrO_2 coatings under the conditions of water quenching and flame jet are studied , the ANSYS software is used to calculate the thermal shock behaviors of coating under two conditions .

采用循环水淬和脉冲激光冲击法并结合有限元计算考察和分析了用超高压梯度烧结方法制备的W/CuFGM的抗热震性能。

Thermal shock behavior of W / Cu FGM fabricated by graded sintering under ultrahigh pressure ( GSUHP ) was investigated and analyzed via water-quenching , cyclic pulsed laser impact and finite element analysis .

水淬高炉矿渣（BFS）是炼铁厂的副产品，具有水硬性质，目前已广泛用于建筑水泥&矿渣水泥的生产。

Water-cooled blast furnace slag ( BFS ), a by-product of iron plants , characterizes hydraulicity , and has largely been put into production of BFS-cements for the purpose of construction .

用X射线衍射、透射电子显微镜、场致发射扫描电镜和电子探针研究了Co72.7C11.8Si15.5合金在1000℃均匀化退火7d后，水淬至室温的相变和相结构。

The structure and phase transformation were investigated for Co 72.7 C 11.8 Si 15.5 alloy homogenized at 1 000 ℃ for 7 d , then quenched in water by means of X ray diffraction , TEM , FESEM and EP .

用水淬熄法研究了Ti-B4C-C系自蔓延高温合成（SHS）反应火焰喷涂TiC-TiB2复相陶瓷涂层的反应过程与机理。

Using the self-propagating high-temperature synthesis ( SHS ) technology , the procedure and mechanism of reactive flame spraying TiC-TiB_2 multiphase ceramic coatings with Ti-B_4C-C system were studied by means of water quenching method .

工艺过程为：1000℃奥氏体化，然后以10℃/s的冷速冷却到变形温度（从A（e3）840℃到A（r3）780℃），变形以后立即水淬。

The temperature of austenitization is 1000 ℃ followed by cooling to the deformation temperature ( from A_ ( e3 ) 840 ℃ to A_ ( r3 ) 780 ℃) . After deformation , water quenched is followed immediately .

YG8硬质合金喷嘴在水淬试验中的失效形式主要是局部块状脱落，集中分布在端面的内孔边缘和外圆柱面边缘。

The form of major damage of carbide nozzle is massive fall off , concentrated in the inner edge of the hole and the edge of the outer cylindrical surface after water quenching test .

探讨了回火温度对低碳Mn-Si-Cr钢的空冷无碳化物贝氏体/马氏体复相组织及水淬马氏体组织强韧性的影响。

Effect of tempering temperature on the combination of strength and toughness of air cooled carbide free bainite-martensite ( CFB / M ) microstructure and water quenched martensite ( M ) microstructure for a low carbon Mn-Si-Cr steel is experimentally investigated .

水淬含钛高炉渣的酸解研究

Study on the Sulfuric Acid Dissolution of Water-quenched Ti-bearing Blast-furnace Slag

以高炉水淬渣为吸收剂处理烧结烟气工业实践

The industry practice of treating sintering gas with blast furnace slag

用于充填采矿的高性能水淬渣胶凝材料

High - performance Gelled Material from Water Quenching Slag for Backfilling

水淬渣作吸附剂处理含铜冶炼工业废水的研究

Treatment of Copper Smelter Wastewater with Water Granulated Slag as Adsorbent

水淬黄磷矿渣加热过程的研究

A study on the heating process of granulated yellow phosphorus slags

高炉水淬矿渣固井液配方与性能研究

Studies on Composition and Properties of Blast Furnace Slag Cementing Fluids

水淬矿渣微细粉配制水泥的研究

Research on super-fine powder in water quenching slag for cement production

量化水淬和盐水淬冷却特性及淬火畸变研究

Cooling Characteristic and Quenching Distortion with Quantifying Water and Brine Quenching

高炉锰铁水淬矿渣活性的研究

Study on reactivity of water - quenched slag from Fe-Mn BLAST FURNACE