汽轮发电机

Reduce分析法可大为简化联接刚度对核电百万千瓦级汽轮发电机轴系的动力特性影响之研究。

It is much more simplified to study the influences of connection stiffness in shaft system for the million - kilowatts - class nuclear power turbogenerator by the Reduce - Analysis method .

国产首台600MW汽轮发电机转子厂内动平衡试验

Rotor Dynamic Balance Testing of the First National 600 MW Turbogenerator

考虑时滞影响的汽轮发电机汽门开度的广域H∞控制

Wide-area H_ ∞ Control of Steam-valving System of Steam Turbo Generator with Time-delay Considered

H2/H∞混合控制在汽轮发电机调速系统中的应用

Application of Mixed H_2 / H_ ∞ Robust Control in Turbo-generator and Governing System

ANSYS模态分析在汽轮发电机转子临界转速计算上的应用

Application of ANSYS Simulation State Analysis to Calculation of Rotor Critical Speed of Turbine Generator

应用DCS实现汽轮发电机的保护控制

Protective control for turbogenerator with DCS

Hamilton正则方程体系下大型汽轮发电机定子系统的振动研究

Study on Oscillation of Large-scale Turbo-generator Stator System under Hamilton Canonical Equation System

20万KW汽轮发电机基础施工的几点认识和意见

Several opinion on 200 MW turbine generator base construction

以一台930MW的水氢氢汽轮发电机为例，计算出了其定子铁心通风孔单元的通风和气体温升，以及每个铁心单元的温升。

The computation results of the stator core ventilation and temperatures of a 930 MW water-hydrogen inner-cooled turbine generator were provided .

采用扩阶的Prony方法识别汽轮发电机基础的结构模态参数

Identification of modal parameter of turbodynamo foundation by augmented Prony method

WX系列汽轮发电机定子嵌线工装应用

The Use of Stator Coil Assembly Tool for WX Series of Turbogenerators

三段式机座600MW汽轮发电机的强度与振动

The Strength and Vibration for 600 MW Turbine-Generator with Three-Section Cone

300MW汽轮发电机励磁机断轴事故分析

Analysis on Shaft - broken Accident of Exciter for 300 MW Turbo-generator

300MW汽轮发电机铁芯温升高的原因及处理

Causes and Treatment of Core Temperature Rise for 300 MW Turbine Generator

300MW汽轮发电机转子现场大修

Locale Entire Reparation of Rotor of 300 MW Turbine Generator

国产300MW汽轮发电机存在的一个超速隐患及改进措施

A Problem of Home-Made Turbine ( 300MW ) and Its Improvement Method

300MW汽轮发电机失磁及失磁保护的探讨

Discussion on 300 MW Generator Magnetism Loss and Its Protection

东方300MW水-氢-氢汽轮发电机结构介绍

The Structure of 300 MW W - H - H Steam Turbo Generator

利用I-DEAS软件的参数化立体建模功能，结合编程软件实现汽轮发电机定子绕组三维参数化自动精确建模系统。

Applying the parametrical modeling capabilities of I-DEAS , an automatic3D parametric modeling system of turbogenerator stator coil was developed .

对600MW级汽轮发电机选型的一些看法

Some Ideas on Selection of 600 MW Turbo generator

600MW汽轮发电机定子冷却水系统运行状况测试及分析

Working Condition Tests and Analysis of Stator Cooling Water System of 600 MW Turbogenerators

300MW汽轮发电机定子端盖灼伤原因及改进

The Scalding Analysis and its Improvement Methods in Stator End Cap of 300 MW Turbogenerator

300MW汽轮发电机计算机辅助培训系统的设计研究

The Design and Research on the Computerized Assistant Training System for 300 MW Turbine Generator

介绍了哈电制造的600MW汽轮发电机定子模态及振动性能试验研究。

This paper presents the mode and vibration test on HEC 600 MW turbine-generator stator .

600MW汽轮发电机可倾瓦轴承损耗计算与试验研究

Calculation of and experimental study on inclinable bush bearing loss for 600 MW turbine power generator

300MW汽轮发电机定子线圈绝缘磨损的原因分析及防止措施

Cause Analysis and Countermeasure for Insulation Worn out of Stator Winding of a 300 MW Turbo generator

100MW空冷汽轮发电机护环强度分析

Strength Analysis on 100 MW Air-cooled Turbine Generator Protecting Ring

200MW汽轮发电机密封油系统的改造

Rebuilding of the Seal Oil System in 200 MW Turbo - generator

200MW汽轮发电机励磁控制系统改进设计

Modification of the Excitation Control System for 200 MW Turbogenerator

1000MW级汽轮发电机转子绕组轴向通风冷却系统

Rotor Winding Ventilation System of a 1 000 MW Inner Cooled Turbine Generator