滚压

gǔn yā
  • rolling;stitching;roll extrusion;rolling depression
滚压滚压
滚压[gǔn yā]
  1. 插接式法兰滚压成型工艺及设备特点

    Roll Extrusion Forming Process of Insert Connection Flange and Its Equipment Characteristics

  2. 利用ANSYS有限元分析软件,对螺旋槽管材滚压成型过程进行了数值模拟。

    Rolling press process of spiral grooved tube was simulated by ANSYS software .

  3. 基于ADAMS的自行式振动滚压夯实机运动学仿真

    Kinematic simulation of self-propelled vibration rolling tamping machine based on ADAMS

  4. 本文通过BP神经网络建立了一个曲轴滚压校直专家系统,以解决曲轴滚压校直过程中校直力的求解。

    In the paper the expert system of crankshaft rolling and aligning was established to solve the alignment power .

  5. α黄铜爆炸、滚压强化后表面层组织结构的TEM研究

    TEM Investigation on the Surface Strengthened Layer of α & Brass after Explosive or Rolled Strengthening

  6. 螺纹滚压强化对300M钢螺纹疲劳强度的影响

    The Influence of Screw Rolling Strengthening on 300M Steel Screw Fatigue Strength

  7. 在ANSYS基础上开发了可以模拟管材滚压剪切过程的应用软件,利用单元死活技术对管材的切断问题进行了模拟。

    The process of roll-cutting tubes was simulated on basis of the principle of large deformation elastic-plastic FEM by ANSYS program and killing element technique .

  8. ZMlMg合金的表面滚压强化

    Surface rolling strengthening of Mg alloy ZML

  9. 曲轴圆角滚压数控系统研究及基于Solidworks的运动仿真

    The Design of the Numerical Control System for Cranshaft Chamfer Rolling and the Imitation of Movement Base on the Software-Solidworks

  10. 用X射线应力测量仪分别测定了坦克履带销经滚压、喷丸和滚压加喷丸三种表面强化后的表面残余应力。

    The surface residual stresses of tank track pins after being strengthened by means of rolling , shot peening or rolling plus shot peening were measured by X-ray stress measurer , respectively .

  11. 利用ANSYS有限元分析软件分别建立曲轴连杆轴颈、主轴颈圆角滚压模型,进行变形分析计算。

    The models of the connecting rods and principal axis neck are built , and the finite element analyses have been done to them by using ANSYS engineering software .

  12. 离心泵和滚压泵对S100β蛋白释放的影响

    The Influence of Roller and Centrifugal Pump on Plasma S100 β Protein Release after Extracorporeal Circulation

  13. 通过滚压刚化表面涂饰和高MOR,得到的坚固、经济的耐火级产品。

    A rolled , rigidized surface finish and high MOR give a tough , economic refractory grade product .

  14. 最终选择变频调速控制系统和电气伺服系统组成PLC控制系统,来完成对冷拉伸滚压设备的自动控制。其次,对冷拉伸滚压设备进行控制方案研究。

    Finally plc control systems , which make up frequency-modulated control speed governing system and electrical servo system , accomplish the automatic control of cold stretching-rolling equipment . Secondly , we study control scheme of the cold stretching-rolling equipment .

  15. 通过X射线衍射法对薄壁滚压前后的表面残余应力进行了测量,并用电解抛光对滚压前后薄壁进行剥层,测量的X方向应力随层深分布的变化。

    The residual stress distribution of thin walled part was measured using X-ray diffraction test . The surface stress distribution before and after rolling was measured , and the stress distribution along the depth was also measured using electrical polishing method .

  16. 本论文参考了大量的有关资料,分析了不同加工工艺特点,最后采用了滚压成型的生产工艺来加工螺旋槽管,其主要结构参数有管材外径d、壁厚t、槽深e、螺距p。

    This paper makes reference to much relevant information and analyzes different technique of machining , and finally adopts roll-pressing to process spirally grooved tube . Main parameters of spirally grooved tube have diameter of tube , wall thickness , corrugation depth and fin pitch .

  17. 研究了300M超高强度钢螺纹滚压和未滚压试样在空气和3.5%NaCl的水溶液中的疲劳性能。

    In this paper , the fatigue properties of rolled and non-rolled screw-thread specimens in 300M ultrahigh strength steel in air and 3.5 % NaCl water solution were investigated .

  18. 486Q曲轴圆角滚压

    Fillet Hard Rolling of Crankshaft of 486Q Engine

  19. 一种WS2加无机粘结剂的滚压膜在上述试验条件下可使微型球轴承得到有效的润滑,可在高温气体流量计上成功应用。

    A roll-pressed inorganic bonded WS2 film gives rise to an effective lubrication for miniature bearing under above testing conditions and has been successfully applied to a high temperature gas measuring flowmeter .

  20. 根据轮辋滚压一次成形工艺方案,使用DEFORM-3D软件对轮辋滚压过程进行数值仿真,研究合理的轮辋一次滚压成形的加工参数。

    Based on the proposed scheme , using DEFORM-3D software on the rim of the wheel rolling numerical simulation , discuss reasonable rim a roll forming processing parameters .

  21. 根据滚压钳体机构的工作过程,运用杆组分析法将该复杂机构拆分成简单的单杆构件、RRR双杆组和RPR双杆组机构,对其进行运动学分析。

    According to the working process of the rolling clamp body institution , Use rod group analysis to divide this complex mechanism into simple single link 、 RRR double pole group and RPR double pole group institutions , analyze kinematics .

  22. 以东风汽车公司生产6102D2球铁曲轴为例,基于本文的研究成果所开发出的曲轴滚压校直系统在国内具有很好的应用价值。

    The Crankshaft Rolling and Alignment System by applying this research result is very useful , using Dong Feng Motor Company 6102D 2 crankshaft produce as an example .

  23. 对经正火、气体氮化、圆角滚压三种工艺的球墨铸铁曲轴进行弯曲疲劳试验,测出其疲劳极限M-1(50%)分别为1471、1935和3010N·m。

    As bending fatigue test result , the bending fatigue limite M - 1 ( 50 % ) of three sorts of nodular iron crankshafts treated with different processes including normalization , gas-nitridation and round cor-ners rolling , was respectively : 1471,1935and3010N · m.

  24. 纸巾滚压模的建模及数控加工

    Modeling And NC Manufacturing of Rolling - Forging Die for Towel

  25. 曲轴圆角滚压运动及结构参数的优化设计

    Optimal design on moving and structural parameters of crankshaft chamfer rolling

  26. 汽车曲轴圆角滚压机钳口滚压力及波动分析

    Analysis of the Rolling Force of Automobile Crankshaft and its Fluctuation

  27. 数控椭圆滚压成型机理的计算机仿真

    Computer simulation of the ellipse forming mechanism of numerically controlled rolling

  28. 球体滚压参数对表面质量的影响

    Influences of Ball Rolling Parameters on Surface Quality of Mechanical Parts

  29. 固体润滑膜的滚压涂敷工艺之研究

    A Study of Rolling - Coating Technique for Solid Lubricant Film

  30. 加工花键轴的新型纯机械立式滚压机床

    A New Type Mechanical Vertical Roller Mill for Spline Shaft Machining