烧成工艺

烧成工艺烧成工艺
  1. 采用一次烧成工艺制备了具有电容性和压敏性双功能TiO2陶瓷。

    TiO2 capacitor - varistor ceramics are fabricated by single - fired process .

  2. 含C1矿化物的多元复合矿化剂的烧成工艺

    Burning process using multi-component compound mineralizer containing Cl

  3. 轧膜成型PTCR瓷片平整烧成工艺的研究

    Study on Sintering Processes of Chip PTCR Formed by Roll Process

  4. 本文总结了MgO-SiO2-Al2O3系的高镁瓷配方、增塑及烧成工艺特性的研究过程与应用结果;

    The paper summerizes the research and application of the formula , preform body plasticization and firing of MgO - SiO2-Al2O3 high magnesium ceramics .

  5. 本文分别用快速烧成工艺和放电等离子体烧结技术对添加适当添加剂的TiO2和Al2O3粉体混合物进行烧结。

    In this paper , the mixture of TiO2 and Al2O3 powders with appropriate additives was sintered by fast-speed firing process and SPS techniques , respectively .

  6. 以聚碳硅烷(PCS)为先驱体,经熔融纺丝、不熔化处理和快速烧成工艺制备出性能较好的连续碳化硅(SiC)纤维。

    Continuous silicon carbide ( SiC ) fibers with fairly good mechanic property were prepared from polycarbosilane ( PCS ) resin by melt-spinning , curing and fast heat-treatment processes .

  7. 采用原位反应热压与覆埋烧成工艺,分别制备了Al2O3颗粒与晶须增强Ti-Al基复合材料。

    Ti-Al composites , reinforced with Al2O3 particles and whiskers , were synthesized by in-situ reaction hot-pressing method and embedding sintering method respectively .

  8. 采用空气中的一次烧成工艺,研究了氧化温度对SrTiO3.晶界层电容器试样的介电常数ε、绝缘电阻率p及介质损耗tgδ的影响;

    The effects of oxidizing temperature on the dielectric constant ε, resistivity p and loss factor tg δ 5 of SrTiO_3 boundary layer capacitors single-fired in air were investigated .

  9. 探讨了添加剂种类和烧成工艺参数对SiAlON结合刚玉复相材料性能、相组成和显微结构的影响。

    The effect of the additives category and the sintering craft parameter on the properties , phase constitute and microstructure of SiAlON bonded corundum composites were discussed .

  10. 文中结合研制透明Al2O3陶瓷的实验,从原料纯度、转相温度、外加剂、球磨工艺与烧成工艺等几方面分析了透光性的影响因素。

    According to the experimented results in studying the transparent Al2O3 ceramics , the influence factors of transparency , the purity of initial material , the phase transformation temperature , the additives , the grinding and the sintering schedule , were analysed .

  11. 采用空气中一次烧成工艺,通过性能测定、SEM观察,研究了Ti/Sr比与SrTiO3晶界层电容器材料试样的烧结性能、半导化、显微结构及介电性能之间的关系。

    The relationship between Ti / Sr ratio , sintering properties , semiconducting , microstructures and dielectric properties of SrTiO_3 boundary layer capacitors single-fired in air were investigated through the determination of properties of specimens and SEM observation .

  12. 对近两年从国外发展起来的新型精炼合成渣12CaO·7Al2O3的烧成工艺、物性和脱硫能力进行了试验研究。

    This paper deals with sintering technology , physical properties and desulphurization ability of new refining slag of 12CaO · 7Al 2O 3 , which has been opened up by foreign country in past two years .

  13. 确定了烧成工艺的各个阶段的温度和停留时间。

    Temperature and time in different heating phases were also fixed .

  14. 高铝硅比熟料烧成工艺研究

    Study of the sintering process for the high a / s clinker

  15. 粉煤灰釉面砖低温一次烧成工艺的研究

    Study of Making Fly-ash Ceramic Glazed Tile by Once-sintering at Low-temperature Process

  16. 对富氧燃烧技术在陶瓷烧成工艺中的应用展开了分析与评价。

    The application of oxygen combustion technology in ceramic crafts is analysed and evaluated .

  17. 富氧燃烧技术在陶瓷烧成工艺中的应用

    Application of Oxygen Combustion Technology in Ceramic Crafts

  18. 油滴釉的形成机理及烧成工艺探讨

    Forming Mechanism and Firing Technology of Oil-drop Glaze

  19. 烧成工艺对莫来石增韧泡沫陶瓷强度的影响

    The Influence of Sintering Craft on the Compressive Strength of Mullite Crystal Toughening Foam Ceramic

  20. 在确定釉的配方后,关键是烧成工艺,控制好烧成温度和降温速率极为重要。

    After the determination of formula , the key technics is sinter temperature and cooling rate .

  21. 采用正交试验法确定了釉料配方和烧成工艺条件。

    The firing condition and the glaze composition have been determined by using orthogonal experiment method .

  22. 最后,对氧化铁基气敏元件的烧成工艺进行了比较。

    The different sintering process of the gas-sensing components based on iron oxide has been compared .

  23. 铁矿尾矿矿相组成与制砖烧成工艺关系的研究

    Study on the Mineral Composition of the Tailings of Ferric ore and Firing Process for the Building Bricks

  24. 本文通过对锆英石原料、成型工艺和烧成工艺的研究,确定了锆英石质研磨体的生产工艺。

    The production process of zircon grinders was confirmed by studying zircon mineral , forming and sintering techniques .

  25. 研究了在搪瓷釉中引入磷酸银制作杀菌搪瓷的配方、烧成工艺。

    The formula and firing technology of the bactericidal enamel by adding silver phosphate as bactericide have been investigated .

  26. 高铝硅比熟料烧成工艺宜选用三组份配方。

    The sintering process of the high A / S clinker can select the dose of the third component .

  27. 结果表明:采用二次烧成工艺可以获得球形度高、表面光滑的氧化铝基微球。

    The results indicate that high sphericity and smooth-faced alumina based ceramic microspheres can be obtained by twice sintering process .

  28. 发光陶瓷釉面质量和发光性能烧成工艺方面的影响因素有:烧成温度和烧成周期。

    Five , the surface quality and luminescent capability of luminescent ceramics have two aspect effects : buming temperature and burning period .

  29. 分析比较了广东省内3家新型干法水泥厂熟料矿物组成、烧成工艺和粉磨工艺的差异。

    The difference of clinker mineral composition , burning process and grinding process of three modern cement plants in Guangdong province was compared .

  30. 以萤石尾砂和珍珠岩废矿粉为主要原料,制备出环保型陶瓷透水砖,探讨了原料配方、成型压力和烧成工艺对透水砖性能的影响。

    The effect of raw material formulation , firing process and molding pressure had been probed on the maim characteristics of water permeable ceramic brick .