烧结性

Al－Al2O3粉末成形体烧结性的研究

Study on the Sintering Property of Al-Al_2O_3 Powder-Formed-Body

孝义铝土矿区半软质粘土烧结性研究

The Study of Sintering Behavior of Half-Soft Clay

催化燃烧是提高效率，降低热NOx污染的有效方法，要求活性组分及其载体具有良好的抗烧结性。

Catalytic combustion is an effective method to increase combustion efficiency and reduce NOx thermal pollution .

CeO2对氧化铝基陶瓷的烧结性、力学性能和抗热震性的影响

Effect of ceo_2 on sintering , mechanical properties and thermal shock resistance of alumina matrix ceramics

助烧剂对Al2O3-SiC-C捣打料烧结性的影响

Effect of sintering agent on sintering property of Al-2O-3 - SiC-C ramming mix

中频感应炉用刚玉质干式捣打料烧结性的研究提高SiC陶瓷烧结用真空中频感应炉加热性能的试验研究

Study on sintering property of corundum based dry ramming mix for intermediate frequency induction furnace IMPROVEMENT ON THE HEATING PERFORMANCES OF VACUUM INDUCTION FURNACE FOR SINTERING SIC CERAMICS

研究了两种晶型的TiO2（锐钛矿型和金红石型）作为添加剂对烧成镁钙砖烧结性的影响。

The effects of two crystal types of TiO 2 ( anatase and rutile ) as additives on the sintering of fired magnesia-calcium brick are investigated .

采用中间相细颗粒表面活化调整的方法，使R值保持在0.2～0.3之间，可提高无粘结剂炭素材料的自烧结性和强度。

By means of activating the surface of the pitch mesophase powder and maintaining the R value between 0.2 and 0.3 , the self-sintering function and strength of the binderless carbon materials can be raised .

对于添加Si的复合材料，通过原位生成的SiB6提高B4C材料的烧结性，并通过进一步加入SiC晶须制备了B4C-SiCw-SiB6陶瓷复合材料。

B_4C is reinforced and flexed by the generation of SiB_6 in suit . To improve the fracture toughness of the B_4C composites by adding whiskers .

SOLGEL法具有纯度高、颗粒细等优点，其主要不足为凝胶干燥时收缩性大，粉体材料的烧结性不好；

The Sol-gel process is characterized by higher purity and smaller size products , but its disadvantages are as follows : great shrinkage during Sol-gel drying and poor sintering property of powdered materials .

因此，必须采用烧结性良好的UO2粉末和合适的成型烧结条件以使开口孔隙度和细孔隙度降至最低。

So that , it is necessary to adopt very sinterable UOt powder and suitable pelleting and sintering conditions to minimize open porosity and small porosity .

锆英石对镁砂烧结性及其制品性能的影响

Effect of ZrSiO_4 on sintering of magnesia and properties of the product containing magnesia

氧化铝陶瓷蓄热体的烧结性及抗热震性能研究

Study on the Sintering and Thermal Shock Resistance Performance of the Al_2O_ 3 Ceramic Regenerator

添加铬矿粉能提高其烧结性，改善其基质组成，增大熔渣与干式料润湿的二面角，且铬矿粉溶于渣后，提高了熔渣的粘度。

Adding chromite powder to it can promote its sintering properties and the constitution of matrix , increase the wetting dihedral angles of solid-liquid , and the chromite powder dissolving into slag can increase the viscosity of slag .

它具有光学各向异性，自烧结性和自粘结性等特点。其粘结性能优良，在高温碳化时会发生强烈的收缩，由此可以得到高强度和良好成型的碳块。

It has properties of optical anisotropy , self-adhering and self-sintering etc. It has excellent self-adhering ability and it will shrink intensely during the carbonization at high temperature , which make high strength and perfect moulding Activated carbon monolith .

其主要研究结果如下：应用KH-570硅烷偶联剂改性SiC颗粒后，明显改善了SiC颗粒的激光烧结成形性。

The primary research results are as follows : The SLS molding rigidity of SiC particles has been improved greatly after modification of KH-570 coupling silane agents .

反应烧结透气性陶瓷-金属复合材料的相结构分析

XRD analysis of reactively sintered gas - permeable ceramic - metal composite

酒钢强磁选红精矿添加生石灰烧结工业性试验

Industrial test on sintering of Jiuquan hematite concentrate from high intensity magnetic separator with addition of lime

运用最优化理论在烧结统计性模型上寻优，得出了获得最佳烧结指标值时的各种矿的定量搭配关系。

Based on the mathematical model of ore matching with the optimal theory , the numerical relationships between one ore with the others were given while obtaining optimum sintering indexes .

合金元素Ni、Mo、W及熔渗铜对烧结钢耐磨性的影响

Influence of alloy elements Ni 、 Mo 、 W and copper infiltrated on wear resistance of sintered steels

工艺参数对TiO2-Ag烧结体导电性的影响

Effect of Technical Parameter on the Conductivity of TiO_2-Ag Agglomeration

Cu（2+）、W~（6+）离子的复合B位取代能提高Cu~（2+）在PFN中的固溶量，减少焦绿石相的形成，有利于系统的低温烧结和改性。

PFN , the solid soluble amount of Cu ~ ( 2 + ) in PFN is increased , and both the formation of pyrochlore phase and sintering temperature are reduced , and the properties of PFN ceramics are modified .

铅锌烧结过程透气性状态及热状态优化控制

Optimization Control of Permeability and Heat Status for Lead-Zinc Sintering Process

可压缩烧结材料塑性变形问题的求解方法

The Ways of Evaluation on Plastic Deformation for Compressible Sintering Materials

添加磷提高烧结黄铜塑性和强度的机理研究

Improving of Plasticity And Strength of Sintered Brass By Adding Phosphor

烧结过程透气性指数的神经网络软测量模型的研究

Permeability index study on sintering process using neural network soft sensor model

提高三角形金刚石多晶烧结体耐磨性的研究

Study on improvement of wear resistance of triangle diamond polycrystalline sintered compact

铅锌烧结过程透气性的智能集成建模与优化控制

On Intelligent Integrated Modeling & Optimized Control over Permeability of Pb-Zn Sintering Process

岩体变形特征；烧结体塑性理论

The deformational characteristics of rock bodies ; ON THE PLASTIC THEORY OF SINTER

低灰份太西洗煤用于烧结的工业性试验

Industrial test of sintering with washed low ash coal