膨胀量

给出因X射线辐射引入的热载荷所产生的金属吸收层衍射图形尺寸膨胀量及金属吸收层热应力的计算结果。

The changes of diffraction pattern and the thermal stresses in absorber caused by X ray radiation were calculated .

同时分析了自由膨胀量和CBR浸水膨胀量的关系，提出了CBR浸水膨胀量的要求。

Meanwhile it makes an analysis of the relationship between free swelling amount and CBR soaking swelling amount , and puts forward the requirements of the latter .

结果表明，补偿收缩石屑砂浆的水中养护最终膨胀量随着UEA或MgO掺量的增大而增大；

Results show that the final expanding quantity of shrinkage compensating crushed stone mortar in the water increased with the increase of UEA or gentle MgO ;

采用20%的Ⅰ级粉煤灰替代水泥，可以把这种砂岩的ASR膨胀量控制在非碱活性范围之内。

The expansion value due to ASR for the sandstone can be reduced to a non-reactive range by substituting cement with 20 % first grade fly ash .

不同区域MgO的膨胀量对结构整体的影响和对延迟膨胀的时间加以控制是外掺MgO微膨胀混凝土技术的两个关键问题。

The influence of expansive volume of concrete mixed MgO in different parts on integrated structure and the control to its delaying time of expansion are the two key problems in MgO concrete technique .

本文分析了模数为2.0,2.2,2.58的三种普通水玻璃砂经过CO2吹气硬化和烘干硬化后的残留强度、高温强度和热膨胀量随温度变化的函数曲线。

The residual bond strength , the high temperature bond strength and the thermal expansion at different temperatures of three kinds of sodium-silicate-bonded sands with silica to soda ratios of 2.0 , 2.2 and 2.58 respectively are reported after curing with CO2 gas and baking in oven .

对山渣料进行了较全面的试验研究，包括击实试验、CBR试验、回弹模量试验、抗压强度试验、浸水破碎试验及膨胀量试验。

The rock-slag mixture has conducted the more comprehensive experimental study , including the compaction test , the CBR experiment , the snapping back module experiment , the compressive strength test , immerses broken experimental and the inflation quantity experiment .

在加工空气压力为0.7MPa（G）、膨胀量与加工空气量之比为25%的情况下，使氧的提取率达到85%~90%。

When pressure of treatment air flowrate is 0.7 MPa ( G ), the ratio between expansion flowrate and treatment air flowrate is 25 % , oxygen extraction rate is achieved 85 % ~ 90 % .

推导了计算公式，计算了BD-2导航卫星的狭义相对论效应引起的时间膨胀量及广义相对论重力势引起的频率变化量。

The frequency shifts caused by the time dilation of special relativity and the gravitational frequency shifts of general relativity for BD-2 are calculated based on these formulae .

试验结果表明：（1）随着竖向应力的增大，GCL的膨胀量不断减小，而GCL的渗透系数则出现先减小后略有增大的规律；

It was indicated that : ( 1 ) swelling of GCLs decreased with the increasing of vertical stress , but the hydraulic conductivity of GCLs decreased at the beginning , and then increased a little ;

冷连轧机工作辊温度场分析及膨胀量预报

Roller Temperature Field Analysis & Thermal Expansion Prediction For of Tandem Cold Rolling Mill

热膨胀量计算在离心压缩机组冷态对中数值验证中的应用

Application of Thermal Expansion Calculation in Alignment of Centrifugal Compressor Group under Cold State

油面上空间不能容纳其膨胀量。

And ④ there is not enough space over the liquid level for expansion .

非标准试样冲击侧向膨胀量合格判定

EXPANDED GRAPHITE Acceptance value for lateral expansion for non-standard impact test specimen of stainless steel

计算各段膨胀量时，定义了膨胀特征温度，用以表征其热膨胀能力。

Expansion reference temperature ( ERT ) is defined to describe the capability of each part .

发现层间和夹心混杂复合材料的热膨胀量随炭纤维相对含量的增加而减少；

The value of the thermal expansion of interlaminar and sandwich hybrid composites decreases with increasing carbon fiber content .

随着碳含量的增加，碳钢γ→α相变引起的膨胀量逐渐减少，γ→α相变产生的膨胀速度逐渐降低。

With the increase of carbon content , the expansion mass and expansion rate induced by γ→α phase transformation is decreased .

同时探索了应用电阻率结构特性指标预测膨胀量的可行性。

Eventually , the feasibility of application of the electrical resistivity property indices on predicating the swell of expansive soils is discussed .

详细讨论了热流道系统的结构与尺寸设计计算、热流道板加热功率的计算、热流道板线膨胀量的计算及线膨胀的克服措施。

The calculation of the size , heating power , linear swell value of hot runner system was also discussed in detail .

文章介绍了炉辊的轴向膨胀量、相对间隙、轴径实际温度及高温氧化减径量。

The paper introduces the axial inflation volume , relative space , temperature of axle neck and high temperature oxidized sizing reduction of rollers .

提出了在模具设计方面应将膨胀量考虑到设计尺寸上，错位问题就能得到解决。

Here the paper presents that expansion factors should be taken into consideration in dimensions design then the offset step problems can be solved .

十六个变形点的计算结果显示了整个分析表面的径向膨胀量大体相等，并与应变计的测试结果作了比较。

The fringe counting results of the sixteen deformational points display the general uniformity of radial expansion over the analyzed area and are compared with strain gage results .

在轴承与主轴支撑面的径向位置上设有的热膨胀量和弹性变形余地。

The radial position between the bearing and the supporting surface of the main axis is provided with a space for the heat inflation and the springy transformation .

在加筋土有荷载膨胀量试验中，取三种不同加筋率的试样进行试验求其膨胀率。

During the swelling capacity test of the reinforced soils under load , three different reinforcement ratio samples are tested in order to reduce their expansion of the soils .

当它们受热时，固体膨胀量最小，液体稍大，气体则最大。

When they get hot , solids make the smallest increase in volume , liquids make a greater increase in volume , and gases make the greatest increase in volume .

在预成形中，通过内部液压和轴向力的合理匹配，使最大膨胀量达到70%的预成形件；

During the preforming , a preform with an expansion ratio of 70 % can be achieved by controlling the relationship between the internal pressure and the axial feeding force .

研究结果表明，膨胀量随初始干密度的增大而增加，随初始含水率和垂直压力的增加而减小；

The results indicate that the expansion ratio increases with the increase in the initial dry density , while decreasing with the increase in the initial water content and vertical pressure .

详细介绍热流道模具浇注系统结构设计和尺寸计算、热流道板加热功率计算、热流道板线膨胀量计算及在设计时应注意的一些问题，并介绍了一种二级脱模机构。

The structure design and the calculation of the sizes , heating power , linear swell value of hot runner system were discussed in detail . A two-step demoulding mechanism was also introduced .

根据前面得到的每发的温升，对制退机每发温升对应的液体膨胀量进行计算，然后通过设计出合理的液量调节器来调节制退液的液量。

According to the temperature rise of Recoil mechanism for a shell , the corresponding volume expansion of liquid was calculated . Then recoil liquid can be regulated through designing the reasonable liquid regulator .

针对生产中存在的控制难点提出了解决办法和设想，通过膨胀量的投入来解决制带初期辊嘴间距的问题。

According to the production process of control difficult proposed solutions and ideas , according to the swelling capacity to solve the problem of the distance between cooling roll and nozzle at the beginning .