电磁兼容性

  • 网络electromagnetic compatibility;EMC;emi;emv;ecm
电磁兼容性电磁兼容性
  1. 美国海军舰船电磁兼容性设计技术综评

    Review of USA navy EMC design

  2. 电磁兼容性测试表明,模块控制器具有较好的工作可靠性和抗电磁干扰的能力。

    The EMC tests show that the module controller installed in electrical power system has good reliability and capacity of resisting disturbance .

  3. 用TEMCELL进行电磁兼容性测试的理论与实践

    Theory and Practice on Electromagnetic Compatibility Tests Using TEM cell

  4. 试论PWM系统电磁兼容性设计的基本方法

    Basic method of EMC design for PWM system

  5. PCB板设计与电子产品的电磁兼容性

    Print Circuit Board designing and the EMC of electronics products

  6. 通过串音预测实现PCB的电磁兼容性设计

    The EMC Design of PCB by Predicting It 's Crosstalk

  7. RFID系统与无线通信系统的电磁兼容性研究

    EMC Analysis between RFID and Wireless Communication System

  8. 通讯设备电磁兼容性(EMC)的结构设计

    Construction Design in Electromagnetic Compatibility ( EMC ) of Communication Equipment

  9. 高速PCB的信号完整性、电源完整性和电磁兼容性研究

    Study of Signal Integrity , Power Integrity and Electromagnetic Compatibility in High-Speed PCB

  10. 最后按照电磁兼容性设计进行了PCB板的设计。

    Finally we design the PCB board according to the design of electromagnetism compatibility .

  11. 结构设计中的电磁兼容性(EMC)设计

    Electromagnetic Compatibility ( EMC ) Design in Construction Design

  12. 所以,信号传输中的信号完整性(SI,SignalIntegrity)问题和电磁兼容性(EMC,Electromagneticcompatibility)问题成为了现代电路集成中的两个最主要的问题。

    Thus , Signal integrity and electromagnetic compatibility during signal propagation turn into the two main problems of modern circuit integration .

  13. 电磁兼容性(EMC)测试技术探讨&接收系统灵敏度和接收机带宽的选择

    Discussion on EMC Measuring Technique & Selection of Receiving System Sensitivity and Receiver Bandwidth

  14. PCB作为电气功能的承载体,其电磁兼容性更加不容忽视。

    As a carrier of electrical function , electromagnetic compatibility of PCB should not be overlooked .

  15. 电磁兼容性(EMC)试验自动测试系统的研制

    A Design of EMC Automated Test System

  16. 改善国产弧焊逆变机电磁兼容性(EMC)的研究

    A Study on the Measures to Improve the EMC of the Domestic Arc Welding Inverter

  17. 用LVDS技术改进LCD控制器的电磁兼容性

    Apply LVDS Technology to Improve LCD Controller 's EMI Performance

  18. 系统通过六层PCB板设计、电磁兼容性设计,大大增加了设备的可靠性。

    The reliability of system is improved profoundly through the design of the six layer PCB board and EMC .

  19. 设计的组合天线具有良好的电磁兼容性,仿真结果表明该天线对于接收“北斗”和GPS信号都具有较好的圆极化轴比和增益方向图。

    The simulation indicated that the polarization axial ratio and antenna gain pattern of this antenna are good for " BD-1 " signal and GPS signal .

  20. 宽带VHF雷达的电磁兼容性系统设计

    The System Design of Electro-Magnetic Compatibility ( EMC ) for Wide Band VHF Radar

  21. 论文的创新之处和解决的关键问题:1:通过大量的综合试验确定了适合回流焊系统的PID参数整定规则2:对基于微控制器的控制系统进行了电磁兼容性研究。

    The innovation and key problem to this thesis is to ascertain PID tunning rules by a great deal of experiments , study syetem 's EMC problems .

  22. 对直流PWM功率放大器的电磁兼容性进行了分析,提出了抑制PWM功率放大器干扰的几种措施;

    The EMC of DC PWM power amplifier is analyzed and several measures to restrain the disturbances of PWM power amplifier are put forward .

  23. 最后研究了载体上天线间的电磁兼容性,计算了天线间的隔离度和天线对平台RCS的影响。

    The isolation among antennas and the effect of the antennas on the RCS of the carrier are computed .

  24. 用电路代替8H电感提高电话机的电磁兼容性

    Using circuit instead of 8H iron inductance to enhance EMC of telephone

  25. 我国信息政策与法规的国际兼容性研究电磁兼容性(EMC)要求在实施过程中的困难及对策

    Study of International Compatibility in Chinas Information Policy and Law Difficulty and counter-measure of EMC requirement in the process of implementation

  26. 根据电流图及近场分布图,分析PCB的电磁兼容性,并加以改进,优化版图设计。

    According to the current plot & near field plot , wecan analyze the EMC of the PCB and optimize the layout design .

  27. 开关功率变换器中应用双随机调制技术能有效地减小传导EMI,改善系统电磁兼容性,但引起了变换器输出电压脉动增加,精度降低。

    Dual randomized modulation used in power converters can effectually reduce conduct EMI , while it increases output voltage fluctuations .

  28. 文章综述了在系统电磁兼容性(EMC)测试中替代直接辐照的电流注入技术的最新研究成果。

    This paper discusses the research and development of current injection techniques instead of radiated electromagnetic field for system level EMC testing .

  29. 本文介绍了数控系统开关电源电磁兼容性EMC涉及的内容,然后提出开关电源电磁兼容性的设计方法。

    This paper introduces the content of electromagnetic compatibility ( EMC ) of CNC system switching power source and design method of it .

  30. 通过对整机线缆之间串扰的分析,运用有限元软件为工具进行电磁兼容性预测并初步建立了针对整机布线软件的EMC知识库。

    Through analysis of cross-talk noise between cables , a method of Predicting electromagnetic compatibility by using FEM simulator is presented in this paper .