直流偏置电压

成像电路为红外扫描焦平面阵列提供直流偏置电压、积分信号和时钟信号，对探测器的输出进行8路数据采集与排序，然后将排序结果输出给上位机。

The circuit provided the DC offset voltage , the integral signal and clock signal . At the same time , the 8-path signals of sensors ' output were acquired and sorted , then the output of sorting was sent to the host computer .

目前偏置电压控制系统大多基于模拟信号进行，而本文以近年来被广泛使用的数字信号处理器（DSP）为中心搭建了MZ电光调制器直流偏置电压控制系统。

This paper however developed and built a MZ modulator bias control system with the center of the digital signal processor ( DSP ) which is used widely in recent years .

用牛顿迭代法分析可解得输入Ebers-Moll模型的直流偏置电压。

Using Newton iteration analysis solution may get the DC bias voltage of inputting Ebers-Moll Model .

考虑直流偏置电压影响的弹性悬臂微梁挤压膜阻尼新模型

A squeeze-film damping model for flexible cantilever microbeam under the effect of DC bias voltage

通过调节直流偏置电压和调制深度，来控制调制器透射曲线。

By adjusting the direct-current bias voltage and modulation depth , the shape of transmission curve can be controlled .

讨论了入射光谱分布对调制灵敏度的影响，以及波导电极直流偏置电压对保证调制灵敏度的作用。

The effect of the incident light spectrum and the waveguide electrode 's DC bias voltage on the modulation sensitivity is discussed .

文中详细地分析了高速脉冲与直流偏置电压Voffset、选通脉冲的关系。

The relationship of high speed pulse on the dc biased voltage V_ offset and the strobe pulse is researched detailedly in this paper .

由此得到可以通过改变外加直流偏置电压推算表面静电势值的新方法。

A new method that the calculate the surface electrostatic potentials can be get by changing the supplied direct-current ( DC ) bias voltages was presented .

其中包括时序逻辑驱动电路、直流偏置电压电路及单芯片焦平面温度控制电路。

The circuit includes a sequential logic drive circuit , a DC bias voltage circuit and a monolithic temperature control circuit for the focal plane array .

实验中通过控制电源频率，直流偏置电压，镀液浓度等参数可以得到形态各异的金纳米线。

Various shapes of the gold nanowires can be achieved by controlling the power supply frequency , DC bias voltage , electrolyte concentration and other parameters in the experiment .

实现的检定项目包括：脉冲输出幅度，脉冲上升沿，脉冲宽度及频率，内触发延时，和直流偏置电压等技术参数的检定。

The realizable verified items are the parameters of pulse output range , pulse raise edge , impulse width & frequency , inner trigger delay , DC volts deflection , etc.

对电容式加速度计，为测量其电容的变化，通常需要带直流偏置的交流电压信号来驱动。

For capacitive sensing , driving signal with DC bias voltage and AC voltage is usually necessary for the measurement of capacitance .

在输出级3V直流偏置时最大输出电压摆幅可达25Vpp。

The maximum modulation voltage is over 2.5V pp corresponding to a 3V DC bias for output stage .

对励磁电流进行谐波分析，研究了直流偏置量和交流电压对各次谐波分量的影响。

Harmonic analysis of magnetizing current is performed to observe the effect of DC bias and alternating voltage on each harmonic component . 2 .