锯片

研制干式切割黑色金属专用锯片的可行性分析

A Feasibility Study of Research and Development of Saw Bit for Without-Water Cut of Ferrous Metal

低温电镀人造金刚石锯片pH对低温镀铁组织形貌及性能的影响

Effect of pH on structure morphology and properties of low-temperature iron plating

高功率CO2激光焊接三明治金刚石锯片

Higher Power CO_2 Laser Welding Technology for Sandwich Diamond Saw

PLC控制自动推杆式小锯片烧结设备的研究

PLC controlled automatic push-rod type sintering furnace for small diameter saw blade

木工圆锯片CAD系统

CAD System of Woodworking Circular Sawblade

木工圆锯片CAM技术

CAM Technology on Wood Working Circular Saw Blade

基于ANSYS的热锯机锯片有限元模态分析

Finite Element Mode Analysis of Saw Blade of Hot Sawmill Based on ANSYS

研究中用X射线应力检测仪对球面多点加压适张后锯片内的残余应力进行了测定。

The residual stresses of the saw-blades caused by the multi-spot pressure tensioning were tested using X-rays .

介绍了莱钢大型H型钢生产线冷锯锯片产生裂纹原因的研究与分析。

This paper analyses the reasons of crack on the cold saw blade from Laigang Heavy H-Beam production line .

采用XRD及SEM等手段，对部分预合金化前后金刚石锯片胎体的组织结构及性能进行了测试分析。

Structure and properties of diamond saw segments before and after partial prealloying were analyzed by SEM and XRD .

本文旨在深入研究高功率CO2激光切割、焊接三明治金刚石锯片的工艺问题及其机理。

This thesis aims to deeply study the high power CO2 laser cutting and welding technology and mechanism for sandwich diamond saw blades .

利用X射线衍射分析和扫描电镜，研究了金刚石锯片激光焊接接头的成分和组织，并测试了接头的力学性能。

The composition and microstructure of the diamond saw blade joint welded by laser welding were studied using X ray diffraction and SEM , and the mechanical properties of welded joint were measured .

锯片变形检测系统硬件设计的目标是设计制作一块PCI数据采集卡，具体包括变形量数据采集、角度量数据采集和PCI总线接口三个方面。

The aim of hardware development is to design and make a PCI data acquisition card , including distortion-data acquisition , angle-data acquisition and interface of PCI-Bus .

■100mm金刚石小圆锯片的研制及应用

Preparation of a ■ 100mm diamond circular saw slice and Its application

在木工圆锯片CAD的基础上，利用2个模块，将CAD产生的数据转换成NC指令，用通用算法语言实现自动编程，并在数控电火花线切割机上进行了加工，取得了满意结果。

Based the CAD technology of the wood working circular saw , NC codes are produced in common computed language by two change programs , cut workpieces on linear cutter are satisfied with production .

其次，用VISUALBASIC语言开发了钢轨和槽钢的锯切功率计算分析程序，为正确地选择锯片电机功率提供了参考。

Secondly , it develops the computational and analytic program of the sawing power for rail steel and channel steel with Visual , Basic language , it will offer correctly reference for us when we choose power of saw blade motor .

锯切过程中锯片承受的总锯切力和单颗金刚石磨粒承受的平均载荷都随着锯切深度ap或进给速度vf的增大而增大；

During the sawing process , the total sawing forces acting on the saw-blade and average loads acting on each diamond grit increase with the depth of cut ( ap ) or the feed speed ( vf ) .

本文对“M2”高速钢板制造的锯片铣刀所作的热处理工艺试验、红硬性试验和刀具寿命试验进行了分析。

In this paper , with respect to M2 HSS saw blades , a series of experimental analysis is performed with heat treatment , red hardness and tooling life .

此外，X射线检测时，在适张前后，锯片切线方向皆为拉应力，而径向为压应力。

Through X-rays test , it was found that the residual stresses in a tangential direction of the saw-blades were tensile stresses , whereas the stresses in a radial direction were compressive stresses both before and after tensioning .

在3种预合金粉锯片中，Cu基预合余粉锯片切割速度最快，Ni基预合金粉锯片切割速度最慢，但是它切割寿命最长，Fe基预合金粉锯片切割寿命最短。

In three component pre-alloyed powder saw blade , Cu matrix saw blade 's cutting speed is fastest , Ni matrix is the most slow but cutting life is longest , Fe matrix cutting life is shortest .

使用一般金刚石与使用熔盐镀Ti金刚石的金刚石锯片相比，金刚石的脱落度由72.2%降至32.3%，减少39.9%；

A comparison of the diamond saw blade using ordinary diamond with that using Ti-plated diamond reveals that the desquamating grade of diamond reduces from 72.2 % to 32.3 % , representing a decrease of 39.9 % ;

该文介绍了用X射线衍射测定圆锯片表面初始残余应力的基本原理，并且用它对圆锯片表面的残余应力进行了测量。

The paper introduces the principle of measuring residual stress on the surfaces of circular saw by X ray and puts forward a new method that incident direction angle of X rays is defined , and measures the original residual stress in the circular saw .

结果表明：烧结温度、Fe含量和金刚石粒度是影响金刚石锯片寿命的最主要因素，而Fe含量，保温时间和Ni含量是影响胎体对金刚体包镶能力的主要因素。

The results showed that Fe and Ni contents and keeping time were the key factors which influenced the retention of diamond in the bond while the sintering temperature , Fe content and diamond size were the key factors which influence the tool life .

实验结果表明，金刚石锯片刀头用Cu、WC、Co作为粘结相可改善对固溶相的润湿性，同时添加少量Fe、Ni、Zn作粘结添加相进一步改善性能；

Experimental results showed that bonding phases such as Cu , WC and Co improved the infiltrating property to the solid solution phase and properties of diamond saw segments can be further improved by adding Fe , Ni and Zn as additive bonding phases .

基于S7-200PLC的小锯片连续烧结炉温度控制系统的设计

Design of temperature control system for small diameter saw blade sintering furnace based on S7-200 PLC

Φ2200mm圆盘摩擦锯片性能的提高

Enhancement of saw blade performance of Φ 2200mm circular saws

采用霍尔传感器US5881来提供检测锯片的零度线信号。

We use a HALL-IC , US5881 to provide the zero-line signal of the saw-blade .

为此，DeBeers工业金刚石部根据广泛的试验室实验和确证的现场数据，制定出其锯片金刚石产品的标示图系，以便金刚石工具制造厂家能够选择最合适的锯片金刚石磨粒。

On the basis of extensive laboratory testing and corroborated data from the field , De Beers Industrial Diamond Division has developed the indicator system for its diamond saw grit products to assist the toolmaker in the selection of the most appropriate diamond saw grit .

对比实验表明，在相同胎体配方与工艺条件下，有序排列锯片的锯切效率比常规锯片提高20%-30%，锯切速度高达7m／min以上。

The comparative test for cutting granite indicated , the cutting efficiency of saw blade has increased by twenty to thirty percent as compared with conventional saw blade on the same matrix and sintering condition . The cutting speed is more than 7 m / min.

本文针对这种现象进行分析研究，对材料为W（18）Cr4V的锯片铣刀进行热处理和性能试验，根据产生变形、裂纹的原因，提出了有效的热处理方案，从而提高锯片铣刀的性能。

The heat treatment , performance test on saw-tooth milling cutters made of W_ ( 18 ) Cr_4V were performed respectively . The cause for deformation and flaw was found . An efficient heat treatment plan was proposed and the performance of saw-tooth milling cutters was improved .