凸缘

将前万向节或CV万向节上的标志与车轴小齿轮轴轭或凸缘上的标志对准。

Align mark on front universal joint , or CV joint , to the mark on the axle pinion yoke , or flange .

文本的研究工作主要集中在以下几个方面：首先，针对Q450NQR1高强度钢板进行典型的V形件和带凸缘的U形件成形数值模拟。

This paper is mainly focused on the following aspects : First , research on the deformation process and springback of the typical V-shaped parts and U-shaped parts with a flange .

胃的下方及侧面凸缘是胃大弯。

The inferior and lateral convex border of the stomach is the greater curvature .

GT避震口尤其是特别开发的品种，我们采用了各种独特的加工方法与现代化的凸缘卷边接合技术等等。

GT flexible duct connector , especially for the special products , we use a variety of distinct processes and modern Wulstumlage joint technology , etc.

V1，B5安装方式电动机的凸缘端跳径跳超差分析及其解决方法

Analysis for Oversize of Flange End Jump and Radial Jump and Resolution Method of them for Motor of V1 , B5 Mounting Arrangements

分析了V1，B5安装方式电动机的凸缘端跳、径跳超差原因，并提出解决问题的方法。

This paper analyzes the cause for oversize of flange end jump and radial jump and present the method for solving the problem .

综合分析表明：本次凸缘失效属于奥氏体不锈钢304H在含氯离子的高温高压蒸汽环境下发生的应力腐蚀开裂。

So in this case , 304H austenitic stainless occurred SCC in the high-temperature , high-pressure steam and chlorine environment .

KD-002凸缘锻模设计及成形过程有限元分析

Finite Element Analysis of the Design and Forming Process of the KD-002 Flange Forging Die

当护栏底部凸缘高为150mm时，则车辆的前、后轮均不能爬上护栏斜坡。

While the height of convex barrier flange at bottom is 150 mm , the front wheel and rear wheel of truck can 't climb up concrete barrier slope .

对Q235B、双相钢DP590和试轧钢板进行的扩孔试验结果表明，试轧钢板亦具有良好的延伸凸缘性能。

The results of under-reaming experiment for Q235B , DP590 and the test steel showed that the test steel has excellent flange elongation .

结果表明，当塑料熔体压力从30MPa增大到50MPa时，铝板凸缘区已基本不再参与变形，铝板上两个板厚减薄较严重的大塑性变形区在此阶段形成。

The results show that the flange of the aluminum sheet has almost no any further deformation and that two highly strained zones with severe thickness reduction are developed when the plastic melt pressure increases from 30 ? MPa to 50 ? MPa .

凸缘圆形件落料-拉深-冲孔复合模设计

The Design to Blanking-Drawing-Punching Compound Die of Circular Parts with Flange

六角凸缘面螺栓冷切挤工艺及模具设计

Cold Upsetting-Extruding Technology and Die Design of Hexagon Flange Head Bolt

带支柱与凸缘开孔球罐最大应力

Maximal stresses of large-scale spherical tanks with stanchions and flanged openings

该凸轮上有3个，4个或6个凸缘。

The cam may have three , four or six lobes .

椭圆形封头凸缘法兰的应力分析及试验研究

Stress Analysis and Test Research of Lug Flanges in Ellipsoidal Heads

非正态分布的汽车半轴凸缘的可靠性稳健设计

Reliability-based Robust Design of Automotive Semi-axle Flange with Non-normal Distribution Parameters

外载荷作用下凸缘联接系统的受力与变形分析

Load-deformation Analysis of a flanged Connection System Subjected to External Loads

杯拉深凸缘皱曲预测与控制

Prediction and control of flange wrinkling in cup DEEP-DR awing process

带凸缘筒形件拉深工艺设计的改进

Design improvement of drawing process for cup-like parts with flange

带凸缘密封固定盖级进模设计

Design of progressive die for fixing cover with flange seal

所有的入码器是可得的在同步器凸缘和夹子中装凸缘版本。

All encoders are available in synchro flange and clamp flange versions .

传动轴主动齿轮凸缘主动齿轮轴承抛油环

Propeller shaft pinion flange main drive gear bearing oil slinger

底带凸缘深杯形件挤压工艺及模具设计

Extrusion Technology and Mould Design for Deep-Cup-Typed Component with Flange on Base

将防水饰条安放在与每个角落刻痕对齐的凸缘上。

Position weatherstrip on flange aligning notches in each corner .

无凸缘方盒形件拉深成形最佳工艺参数

Optimal technological parameters for the drawing process of square boxes without flanges

高精度微型凸缘无磁钢轴承套圈加工

The high-precision process technology for non-conductive magnet flanged bearing races

IMB14&机座无底脚，端盖有小凸缘，卧式安装；

IMB14-seat without foot , head cover with small flange , horizontally-mounted ;

GB/T7217-1987凸缘外圈向心球轴承凸缘尺寸

Radial ball bearings with flanged outer ring & Flange dimensions

必须给胶粘凸缘均匀涂上一层薄薄的底漆。

The adhesive flange must be coated thinly and evenly with primer .