喷油泵

PS型喷油泵的研制开发

Design of PS Fuel Injection Pump

本文用A、B、C、D四种涡轮增压器和X、Y两种喷油泵与480QZ型柴油机进行了匹配试验研究。

The experimental investigation on matching four kinds of turbocharger and two types of fuel injection pump to a turbocharged diesel engine has been carried out .

柴油机电控喷油泵位置PID控制试验研究

Experimental study of electronic control diesel oil pump based on variable parameter PID

AD型喷油泵燃油喷射系统计算机建模和仿真分析研究

Modeling and Simulation on Fuel Injection System of AD Type Pump by Computer

发展中的轻型车用PM型直列式喷油泵

The Latest Development of PM Fuel Injection Pump for Light-Duty Vehicles

单片机与CPLD在喷油泵试验台中的应用

The application of MCU and CPLD on fuel injection pump bench

基础静态提前角为6（CA。6）、喷油泵。

The basis advance angle of static fuel delivery is 6 ( CA . 6 )、 Pump .

PM型喷油泵研制开发及应用

Development and Application of PM Fuel Injection Pump

在分析燃油喷射系统工作机理以及综合有关相近类型喷油泵喷射系统研究成果基础上，经过分析引入修正系数，建立了AD型喷油泵燃油喷射系统工作模型。

Based on fuel injection system working principle and its studies , a working modeling for AD type pump is established .

基于CPLD的喷油泵实验台转速测量系统设计

The Design of Rotational Speed Measurement System of Fuel Injection Pump Bench Based on CPLD

PA6可变喷射正时喷油泵的优化设计

Optimization Design of PA6-Diesel Injection Pump with Variable Injection Timing

着重论述了PM型喷油泵的结构特点和具有高喷射压力的技术措施；

This paper emphasizes on recounting structure features and technical measures for high injection pressure of PM pump .

试验结果表明：PM型喷油泵能够全面满足轻型车用柴油机性能以及欧II排放法规要求。

The testing results show that PM pump can meet performance and EURO II emission regulation demands for light vehicle diesel engine .

利用柴油机原有的喷油泵提供压力源，通过双燃料喷油器中的增压泵提高LPG燃料的压力；

And the pressure of LPG fuel is highly increased by using a boost pump inside the injector ;

同时本课题针对工程实际需要，对AD型喷油泵燃油喷射系统涉及到的RFD型调速器特性性能进行了理论研究。

The software is developed for fuel injection system of AD type pump .

喷油泵试验台仅用来驱动康明斯PT喷油器、变速和记录喷油次数。

The test stand of injection pump is merely used to drive the Cummins PT injector , change speed and record number of injection .

日野KL系列发动机柱塞式喷油泵使用和维护简介

Operation , Maintenance & Repair for Plunger-Type Fuel Pump of HINO 's KL Series Diesels

本文以发动机喷油泵中的高温铜焊接件为研究对象，着重研究了高温铜焊接对Ni-P镀层的影响。

The effects of copper welding on Ni-P coating were investigated using components of copper welding in injection pump as sample .

BQ型喷油泵泵体加工工艺的研究

Machining Technology for BQ Type Oil Jet Pump Body

轻型高速BQ型喷油泵的设计、应用和发展

The Design , Application and Development of Light-duty High-speed BQ Type Fuel Injection Pump

对AD、MW型两种喷油泵，在6110Z型柴油机的典型工况下，进行了匹配对比试验。

Comparative matching tests of two models of injection pump , AD and MW on 6110Z diesel engine have been carried out under typical conditions .

还测试分析了燃油温度和燃油中DMC含量对顶隙柱塞喷油泵喷油特性的影响规律。

The effects of the Top Clearance Plungers parameters , the fuel temperature and the DMC content in the fuel on the fuel injection law have been investigated .

研究结果表明，喷油泵的各缸喷油量不均匀度改善后，发动机缸内最大压力和最大压力升高率明显降低，发动机的NOx排放显著降低，PM排放略微提高。

The results show that , after variation of average injection quantity between cylinders are controlled , cylinder maximum pressure and maximum pressure increase rate become lower ; engine NO_x emission improves obviously ;

同时还详细叙述了针对柴油机欧II排放要求而与PM型喷油泵配套开发的RWS调速器的设计要求与特点。

Meanwhile , this paper recounts designing requirement and features of RWS governor that matches PM pump and aims at demands of EURO II emission regulation for diesel engine .

为了缩短柱塞式燃油喷射系统产品研制开发周期，提出了引入修正系数的AD型喷油泵系统喷射过程理论模型计算机建模的研究方法。

In order to reduce some experiments and cut down the consumption of raw materials needed for modeling of fuel injection process , a theoretical method based on modeling by computer is proposed for research on AD pump fuel injection system .

基于CAE的结构有限元技术，在对某高压喷油泵凸轮轴复杂受力情况作详细分析的基础上，对该凸轮轴的可靠性进行了校核。

This paper is based on CAE structural finite element method , the reliability of the high pressure fuel injection pump camshaft was verified on the basis of the analysis of working condition of the camshaft .

介绍了联邦德国Bosch公司生产的VE型分配式喷油泵的工作原理、维护和故障排除方法。

This paper describes the working principles , maintenance and trouble shooting of the VE distributor type fuel pumps produced by BOSCH Corporation in Federal Republic of Germany .

针对装配6A95Z20型喷油泵的6110A型柴油机在工作过程中减速迟缓的现象，在实验室对因减速迟缓而维修的6A95Z20型喷油泵进行了试验。

According to deceleration retardation phenomenon when the6110A type diesel engine which was assembled6A95Z20 type fuel pump operates , the fuel pump was tested in laboratory .

作者对6130Q柴油机喷油泵，在稳定工况和变速工况中，进行了齿杆位移和供油提前角等运动规律方面的测试研究。

Dynamic behaviors of fuel injection pump control rack displacement and injection advance were studied experimentally on a 6130Q diesel engine at both steady and transient conditions .

试验证明：国产化喷油泵和喷油器的技术性能指标基本上达到了BOSCH公司样品泵的指标，符合德国MTU公司396系列柴油机的技术规范。

The tests show that the technical characteristics targets of the domestically made fuel injection pump and the fuel injector basically reach the standards of the specimen pump of BOSCH , and satisfy the technical codes of German MTU 's 396 series diesel engine .