曲轴箱

qū zhóu xiānɡ
  • crankcase;crankcase set
曲轴箱曲轴箱
  1. 曲轴箱通风系统要携带新鲜的空气通过曲轴箱。

    The crankcase ventilation system carries fresh air through the crankcase .

  2. 曲轴箱处理不正确导致中间轴轴承盖底座处于旋入过深(约1mm)的情况。

    Incorrect processing on the crankcase has resulted in a situation in which the base for the intermediate-shaft bearing cover is milled approx.1mm too deep .

  3. 曲轴箱压铸模温度场分析

    Thermal Field Analysis for the Die Casting Mold of Motorcycle Crankcase

  4. 曲轴箱是发动机气缸体较低的部分。

    The crankcase is the lower part of the engine cylinder block .

  5. 曲轴箱砂芯手工制芯用取芯机械的优化设计

    Optimization Design of Core-Picker in Manual Core Making of Crankcase

  6. 曲轴箱漏气量的测试及其应用

    Investigation on the Amount of Crankcase Blow-by and Its Application

  7. 曲轴箱窜气量检测仪的研制

    Measurement instrument for the blow-by parameters of engine crankcases

  8. 曲轴箱双头螺柱安装方式研究

    A Research on Installing Method of Crankcase Stud-Bolt

  9. 曲轴箱凸轮传动轴衬套

    Crankcase cam gear bushing grain drive shifter

  10. 曲轴箱,航空内燃机用

    Crankcase , for internal combustion aircraft engines

  11. 采用实心铸件飞边后,曲轴箱更适于容纳气体并承受惯性力。

    The solid , cast fins make it best suitable to accept gas and inertia forces .

  12. 曲轴箱连杆密封件损坏。

    Worn crankcase piston rod seals .

  13. 曲轴箱的铸造工艺设计

    Technology Design of Crankcase Casting

  14. 曲轴箱用油起沫试验

    Crankcase oil foaming test

  15. 汽车污染物来自排气管排出的废气、曲轴箱窜气和燃油蒸发等。

    Automobile pollutants come from waste gases exhausted from outlet , blow-by of crankcase and vaporization of fuel .

  16. 曲轴箱润滑油离心分离器

    Crank case oil centrifuge

  17. 摩托车主要排放源分为:曲轴箱窜气、汽油蒸发及排气管排放三部分;

    Sources of motorcycle pollution are blow - by of crankcase , gasoline vaporization and emissions from exhaust pipe , i.

  18. 曲轴箱中气缸盖紧固螺钉的盲孔中不得有油或冷却液。

    There must be no oil or coolant in the blind holes for the cylinder-head fastening screws in the crankcase .

  19. 汽车内泄漏污染物的四个位置是燃油箱、化油箱、曲轴箱和尾管。

    The four places in the automobile from which pollutants can escape are the fuel tank , carburetor , crankcase and tail pipe .

  20. 优异的热稳定性和抗氧化性防止在职石油降解这有助于阻止和污泥过滤器在石油画廊,曲轴箱和阀门列车编组。

    Exceptional thermal stability and oxidation resistance prevents in-service oil degradation which contributes to filter blocking and sludge formation in the oil galleries , crankcase and valve train .

  21. 摩托车的曲轴箱盖是发动机的主要构件,在摩托车发动机运转时,会受到曲轴作用的激振力而发生振动向外辐射噪声。

    Motorcycle 's crankcase cover plate is its engine 's major component , which would vibrate to radiate noise under the force of the crankcase when the motorcycle'sengine operates .

  22. 改造后已连续使用12000小时,结果证明,活塞杆和填料的磨损减少,曲轴箱窜气量变小。

    Continuously running of the improved air compressor for 12000 hours showed that the abrasion between pis-ton rods and packings reduced , while the amount of air leaking to crankcase decreased .

  23. 恒温进气空气滤清器、二次空气喷射系统、催化转换器、排气再循环系统、曲轴箱通风装置及汽油蒸发控制系统等新型排气净化装置,可以抑制有害排放物的产生,使汽车排气得到净化。

    New purifying apparatuses , such as air filter in constant-temperature inlet , second air-injection system , catalytic converter , exhaust recycling system , crankcase ventilation apparatus and gasoline vaporization control system can reduce the forming of harmful emissions to purify automobile emissions .

  24. 在整个建模中,包括发动机的进气系统、排气系统、气缸、曲轴箱、燃油喷射系统、及其一些附件如空气滤清器、三效催化器等模块的建立。

    The engine modeling process includes the modeling of the intake system , the exhaust system , the cylinders , the crankcase , the fuel injection system , and its attachments such as the air filter , and the three-way catalytic converter module .

  25. 而曲轴,在齿轮箱挂挡时,又使汽车持续运动。

    When the gears are engaged , the crankshaft keeps the car moving .