柱塞阀

主要产品包括：柱塞阀、高温球阀、止回阀、截止阀、排污阀、闸阀、波纹管截止阀及民用阀门。

We have many series production such as plunger valve , integral heat ball valve , check valve , close valve , duct valve .

柱塞阀密封环与柱塞间密封过盈配合的计算

The Calculation for Seal Interference Fit between Seal Ring and Plunger of Piston Valve

转储也是可选的柱塞阀。

Also optional Plunger Dump Valve .

介绍了柱塞阀的结构、工作原理及其在煤气站的应用。

The structure , principle and application of plunger - type valves at gas station are introduced .

通过对该阀密封结构的理论分析和试验研究，得出了计算过盈量的经验公式，该公式已在湖州第二阀门厂柱塞阀产品的设计中得到验证。

Through experimental and analysis study of the seal structure , we obtained the empirical formula for the calculation of interference magnitude . It has been used and confirmed in the design of piston valve by Huzhou № 2 Valve Plant .

柱塞节气阀式化油器与等真空膜片式化油器的分析比较

An Analytical Comparison Between Plunger Type Throttled Carburetor and Vacuum Diaphragm Carburetor

标准型抽油泵柱塞上阀罩的工作缺陷是出油孔壁磨损断裂。

The shortcoming of top valve housing for standard type oil well pump plunger is wear and rupture of oil flow pore wall .

这种抽油泵柱塞游动阀采用机械强制开启和关闭的结构，柱塞为等径光管、浮动结构，可防止发生气锁游动阀、阀球关闭滞后、砂卡柱塞现象。

The travelling valve of the pump is designed to be closed and opened forcibly , and the pump plunger adopts equal-diameter bare pipe with a floating structure to prevent gas lock and sand sticking .

采用柱塞式电磁阀的单螺杆压缩机气量调节方法

Technique of Capacity Control for Single Screw Compressor with Electromagnetic Valve

海水柱塞泵配流阀结构及其动力学的研究

Design and Dynamics Study of the Port Valve in a Seawater Hydraulic Piston Pump

柱塞泵单向阀球与活塞直径比值对工作精度的影响

The Influence of Proportionate Value on Piston Pump Working Precision between the Diameter of Piston and Valve Ball

电磁柱塞拉下通气阀，堵住通向活性碳罐的通路。活塞销锁圈，活塞销扣环

The solenoid plunger pulls the vent valve down , blocking off the passage to the charcoal canister . piston pin snap ring

该泵对泵筒、柱塞、固定阀做了设计，改善了泵筒受力状况，提高了螺纹的密封性能和抗拉强度。

The barrel , plunger and standing valve of the pump were designed , improving the barrel 's force conditions and reinforcing the screw thread 's sealing performance and tensile strength .

柱塞式压力扫描阀在压气机试验中的应用

The Use of Plunger Type Pressure Scanning Valve in Compressor Testing

阀配式柱塞泵配油阀运动滞后问题的讨论

Problem of Motion Delay re Distribution Valve of Valve-Controlled Plunger Pump

抽油泵柱塞防断上阀罩的研制与应用

Development and application of break prevention top valve housing for oil well pump plunger

应及时更换已磨损的柱塞及出油阀偶件。

Should be the timely replacement of worn and out of the plunger valve coupled parts .

亚新科天纬的出口产品包括：喷油泵、喷油器、喷油嘴、柱塞、出油阀、汽车零部件加工类。

ASIMCO Tianwei exports diesel pumps , injectors , nozzles , plungers and valves , auto part machining .

这种抽油泵采用等径柱塞，上游动阀罩内无阀球，仅通过螺纹与柱塞上部连接；

The pump adopts isodiametric plunger , and there is no valve ball in its upper traveling valve housing .

柴油机柱塞、出油阀和喷油嘴这三对偶件的磨损直接影响到柴油机的供油规律。

The wear of diesel engine fuel pump plunger , delivery valve andfuel injector has direct effect on the fuel supply law .

为采用变量柱塞泵和溢流阀组合的液压系统提供了一套普遍实用的恒功率输出调节机构。

Offering a whole set of practical constant power output adjusting mechanism for hydraulic system which adopts pillar stopper pump and overflow valve .

我司的主要产品有：油嘴，柱塞，出油阀，VE泵等，所有产品均质优价廉。

Our main products are : nozzle , plunger , delivery valve , VE pump , etc. , all products are quality and cheap .

泉州新固机械有限公司是专业生产大型柴油机配件的企业，如喷油嘴、柱塞、出油阀、缸套，滤芯等。

Quanzhou Xinguang Machinery Co. , Ltd is a leading manufacturer which is specialized in the three modules for fuel injection system in China .

单柱塞油泵的单向阀改成球阀，安全阀改用带导向的锥阀；

The check valve of the single piston pump was replaced by ball valve , and conical valve with guidance was used for safety valve ;

柴油机喷油泵的柱塞、出油阀和针阀这三大精密偶件的磨损程度直接影响到柴油机的供油规律和各种综合性能。

The wear of diesel engine fuel pump plunger and barrel assembly , delivery valve assembly and needle valve assembly has direct effect on the fuel supply rule .

通过实践总结和分析，论述柴油机燃油供给系统三大精密偶件，即柱塞、出油阀和针阀偶件的四种检测方法，为实际操作提供经验。

This paper mainly expounds four inspection means for three big precision coupling of fuel supply system in diesel engine based on the practice , which can be covered for practical operation .

设计的液力反馈型空心杆抽油泵主要由反馈长柱塞、反馈泵筒、出油阀、接箍、旋转装置、工作泵筒、工作柱塞、进油阀等组成。

The designed hydraulic feedback hollow sucker rod pump is composed of feedback long plunger , feedback pump barrel , traveling valve , coupling , rotating device , working pump barrel , working plunger , and standing valve , etc.