热型

结论通过对FUO患者体温的连续监测，对热型、热程、病情认真细致的观察，可为FUO早期诊断和选择有效的降温措施提供依据；

Conclusions In the patients with FUO , continuous observation on the temperature and fever type and fever period and state of disease can provide evidences for the early diagnosis and treatment .

以FC-BGA芯片为冷却对象，建立其简化传热模型，采用热型线法对冲击射流散热方式进行了分析。

A simplified heat transfer model of Flip-Chip BGA packaging was built up . The impinging jet cooling effect was analyzed by Thermal Profile method .

纯金属Al热型连铸凝固过程数值模拟

Numerical simulation of solidification of continuously cast pure Al

热型连铸Al单晶线材的组织演化过程研究

Study of evolvement of forming single crystal Al wire by heated mould continuous casting method

热型连铸φ8白铜杆Ni、Fe、Mn元素的偏析程度则分别降低了30%、65%、55%。

As for the 08 rod , the decrease of Ni , Fe and Mn is 30 % , 65 % and 55 % respectively .

热型连铸制备Cu-Cr合金的研究

Investigation of preparing Cu-Cr alloy by means of continuous casting with heated mould

热型连铸Ag-Cu-Zn合金工艺及其组织

Producing Process and Microstructure of Ag-Cu-Zn Alloy by Heated Mould Continuous Casting Method

热型连铸是一项近净成形（near-net-shape）技术，它是将定向凝固和连铸技术结合起来的一种新型工艺。

Ohno Continuous Casting is a novel near-net-shape process , which combines the directional solidification with the continuous Casting .

在自制的水平热型连铸设备（OCC）上，采用一定的工艺参数，制备出表面呈镜面，内部组织沿轴向定向排列的柱状组织Cu-Al-Ni形状记忆合金。

Using appropriate process parameters , the Cu-Al-Ni shape memory alloy with good surface quality and unidirectional dendritic crystal was prepared by the self-made ohno continuous casting equipment .

计算结果表明，在ARI标准工况下，全新风回热型空调系统的制冷性能系数（COP）高于全新风空调系统2.3倍。

From the calculation results , it is indicated that at the standard ARI conditions , the heat recovery system has a higher coefficient of performance ( COP ) than the full fresh system by 2.3 times .

目的分析不明原因发热（FUO）患者的病因，观察发热热型和热程变化，评价降温护理效果。

Objective To analyze the causes of fever of unknown origins ( FUO ), observe the type of fever and changes of fever process and evaluate the nursing effect .

本文在MTS模型的基础上，以带有同步组装技术的分离式Hopkinson压杆装置为研究手段，对比研究了高梯度定向凝固热型连铸单晶铜和上引法连铸多晶铜的动态力学性能。

By using MTS model and the experimental technique of the split Hopkinson bar with the synchronization assemblage , the dynamic constitutive models of the monocrystal copper made by Ohno continuous casting and the polycrystal copper made by up-continuous casting were investigated .

在自制的水平式热型连铸设备上，选用合适的工艺参数制备出了表面质量良好、内部组织沿轴向均匀分布的Ag-Cu-Zn合金铸棒。

By appropriate process parameters , the Ag-Cu-Zn alloy ingot with good surface quality and even unidirectional microstructure was fabricated on the self-designed horizontal heated mould continuous casting apparatus .

热型连铸法制备具有柱状晶组织的Cu-Al-Be合金丝，消除了传统制备方法中等轴晶晶界的应力集中导致的脆性，显示了优良的力学性能和记忆性能。

Cu-AI-Be alloy which is casted by OCC process has the columnar crystal structure . It had eliminated the traditional polycrystalline material brittleness of equiaxed crystal boundaries with stress concentration , and it demonstrates excellent mechanical properties and memory performance .

采用熔模精密铸造工艺，生产中空螺旋状不锈钢冷却水喷头，其工艺要点是，采用热型重力浇注，在高温下进行自由浇注。

Hollow spiral stainless steel cooling-water-sprayer was produced by investment casting .

寒、热型胃黏膜损伤模型的对比和应用研究

Comparison study of cold or hot gastric mucosa lesion animal models

白铜管热型连铸的温度场

Temperature Fields in the Heated Mold Continuous Casting of Cupronickel Tubes

回热型吸附式空调样机实验研究

Experimental research of a prototype for heat-regenerative adsorption air-conditioning system

回热型吸附式制冷系统的最优运行研究

Research on Optimum Operation of Heat Regenerative Adsorption Refrigeration System

连续回热型吸附式制冷机的改进及运行实验

Improvement and test on a continuous heat recovered adsorption refrigerator

对电流致热型设备红外诊断技术的探讨

On infrared diagnostic technique for current ~ heated electric equipments

热型连铸工艺凝固过程的数值模拟

Numerical simulation on solidification of continuous casting of hot mould

针刺胃经穴位干预胃肠实热型肥胖症瘦素抵抗的临床研究

The Effects of Acupuncture on Stomach-channel on Leptin of Obesity

锌铝合金热型连铸的工艺方法

Technique of producing ZA alloys by heated mold continuous casting

针刺治疗对单纯性肥胖胃肠实热型患者的良性调整作用探讨

Good Regulation of Acupuncture in Simple Obesity Patients with Stomach-Intestine Excessive Heat Type

热型连铸工艺参数的数值分析

Numerical Analysis for Processing Parameters of Ohno Continuous Casting

热型连铸锌铝合金定向凝固线材的组织分析

Microstructure analysis of ZA alloy rod directionally solidified by heated mold continuous casting

连续回热型气-固化学热泵制冷系统的操作优化

Operation Optimization of a Continuous Heat Recovered Gas-solid Chemical Heat Pump Refrigeration System

电压致热型变电设备红外量化检测研究

Study of Infrared Quantitative Detection for Substation Equipment Voltage-Cause-Heated

热型连铸过程的二维稳态传热模型

Two-dimensional steady-state heat-transfer model of ohno continuous casting process