胶垫

  • 网络eva;RUBBER MAT;poron;Cushion
胶垫胶垫
  1. 传统的胶垫密封存在相容性差的问题,在对橡胶密封垫有腐蚀的介质中不能使用。

    Traditional cushion seal has the problem of poor compatibility , it cannot be used in the medium which has corrosive effect on rubber gasket .

  2. 产自西班牙的模切底胶垫,超强耐模切性能、超长耐模切次数、性价比高。

    The rubber cushion with die cutting base made in Spanish has the superfine die cutting resistance and the myriads of die cutting cycle and is most cost effective .

  3. 门奇断流术(PAD);空调器压缩机用减震胶垫的研究

    Development of damping rubber pad used in air-condition compressor

  4. 将平直的瓦楞纸板平放在胶垫上。

    Will be flat on the corrugated board flat on the pad .

  5. 浅谈丁基胶垫与气门嘴的粘合

    Simply Discussing the Sticking of Butyl Rubber Pad with the Air-in Mouth

  6. 模切辊采用汽缸自动分离装置,减少胶垫磨损。

    Die-cutting roller cylinder type auto separation unit can increase wear of rubber sleeve .

  7. 底部设有10个防滑胶垫,防止于锻?时滑倒。

    10 rubber feet on the bottom keep it from slipping on hard surfaces .

  8. 主营缓冲块、发动机胶垫、密封胶条,水箱胶管及空气胶管、汽车线索。

    Buffer block , engine mounting , sealing tape , water hose and air hose , automotive leads .

  9. 注:压盖、胶垫、螺栓螺母通常与件体分开供应。

    Note : the glands , gaskets , bolts & nuts are supplied respectively with the body usually .

  10. 用作密封胶圈、胶垫、门窗封条和铺设工作台及地板。

    Used as a sealing apron , pad , door and window seals and laying of tables and floors .

  11. 在床脚加装胶垫也可以减轻一定的振动感。

    At the foot of the bed pad can also be installed to reduce the vibration of a certain sense .

  12. 混凝土轨枕线路的弹性与轨下胶垫合理刚度工程装备战场抢修性分析

    On the resilience of track with reinforced concrete sleepers and the reasonable rigidity module of Under-Rail bearing plate Engineering Equipment Combat Resilience

  13. 彭敏旭发明的“第三只眼”包括一个半透明的塑料盒,用薄胶垫就可以直接贴在佩戴者的额头上。

    Paeng 's Third eye consists of a translucent plastic case that is fixed directly to the wearer 's forehead with a thin gel pad .

  14. 主要产品有软轴、拉线、发动机支架胶垫、水管、密封条、油封、高压分火线、冲压件等。

    The main products are soft shaft , barrows , engine stents , pipes , the rubber sealing strip , oil seal , high , stamping the subsection , etc.

  15. 把铰链5放到机台的孔上,对准台板橡胶支座6,把头部放到四角的机头胶垫7上。

    Fit hinge 5 into the opening in the machine bed , and fit the machine head to table rubber hinge 6 before placing the machine head on cushions 7 on the four corners .

  16. 然后分析轨道参数如轮轨摩擦系数、轨道轨下胶垫刚度、轨道谐波激扰以及轨底坡等对轮轨垂向动力作用的影响。

    Track parameters such as wheel / rail friction coefficient , track pads stiffness under the rail , track harmonic excitation and rail base slope to discuss related parameters on the influence of wheel / rail vertical dynamic action .

  17. 本文针对圆形截面橡胶悬置胶垫,给出了利用有限元方法和参数识别技术确定压缩刚度经验公式中形状系数的方法与步骤。

    Taking a rubber engine mount of rectangular roundness-section as an example , an approach , based on nonlinear finite element method and parameter identification technique , is presented in this paper to calculate the shape factor of the empirical formulae for compressive stiffness of the mount .

  18. 以胶代垫硅酮密封胶在汽车发动机上的应用

    The application of Silicone Sealants in Automobile Engine

  19. 再生胶鼠标垫配方用量研究

    Study on composition quantity of reborn rubber mouse-pad

  20. 我公司专业生产预硫化工程胎胎面胶、中垫胶;

    We are specializes in manufacturing precured tread rubber tires works , in the rubber pad ;

  21. 研究加工助剂ZD2在载重斜交轮胎胎冠胶和肩垫胶配方中的应用效果。

    The application of processing aid ZD 2 in the crown and shoulder pad compounds was investigated .

  22. 结果表明:以此再生胶做的鼠标垫,其性能指标达到或优于同类产品。

    The result showed that the properties of the mouse-pad mainly made from reborn rubber are similar to ( over ) same products .

  23. 结果表明,EPDM/CIIR共混比为80/20硫化胶有较好的综合性能,比单独使用EPDM作主体材料的减震胶垫减震效果更好。

    The result shows that synthesize performances of EPDM / CIIR devulcanizing blend using in shock absorption were better as its ratio was 80 / 20 , than single EPDM .