镁合金

在对镁合金植入体和骨结合界面的研究中发现：与骨组织接触的镁合金表面生成含有Ca和P的降解产物层。

Microstructure observation showed that a Ca-and P-containing degradation product layer was found at the interface between magnesium alloy implant and bone tissue .

镁合金薄板TIG焊自适应弧长控制

Adaptive arc length control for magnesium alloy sheets TIG welding

焊接工艺参数对镁合金CO2激光焊焊缝表面成形的影响

Effects of welding parameters on CO_ 2 laser welding of magnesium alloys

多波长K系数法同时测定镁合金中的铜、锰、锌

Determination of cu , mn , Zn in magnesium alloys with multiwavelength K-factor Spectrophotometry

结果表明，镁合金化学镀镍层的P含量为6.68%（质量分数），与基体结合良好。

The results showed that phosphorus content of electroless coating was 6.68 % wt , and the films ' adhesion resistance was good .

并在电源参数研究的基础上，研究了TiO2对镁合金微弧氧化的影响。

Furthermore , the influence of TiO2 sol on the MAO of magnesium was also be studied .

铝-镁合金材料磨损后刷镀Ni-P合金工艺

Technology of Ni-P Alloy Brush Plating on Worn Material of Aluminium Magnesium Alloy

采用含CeCl3的净化熔剂对含Ce的镁合金进行精炼，研究了CeCl3对合金中Ce损耗量的影响规律。

The effect of CeCl_3 in flux on the loss of Ce in magnesium alloy during refining was investigated .

镁合金TIG焊工艺

Process of TIG welding on magnesium alloy

变质处理镁合金在SIMA法中的组织演变

Microstructure Evolution of Modification Processed Mg Alloy in the SIMA

利用俄歇电子能谱（AES）进行氧化膜元素深度剖析发现，在含0.3%铍的镁合金液表面生成的氧化膜可以分为3个亚层：最外层为氧化镁层；

AES depth profile analysis showed that the surface oxide film could be divided into three sub layers .

镁合金在3C产品中应用现状及前景展望

Application and Developing Tendency of Magnesium Alloys in 3C Products

试验结果表明富Ce稀土的添加可使镁合金起燃温度提高70℃。

The results showed that the addition of Ce rich RE could increase initial combustion temperature of Mg alloy by 70 ℃ .

结合二元合金相图及镁合金中组元镁的活度系数计算结果，提出采用液态金属Pb作为阴极去除微量杂质Mg。

The liquid lead was recommended as cathode to remove trace impurity Mg2 + according to the binary alloy phase diagram and magnesium activity coefficient calculation .

SiO2溶胶封孔剂可浸入镁合金微弧氧化膜的微孔，形成有效封孔。

It could be observed that the SiO_2 sol sealing agent fills up the hole of micro-arc oxidation coating on magnesium alloy .

利用XPS（X射线光电子能谱）对镁合金石墨砂型铸造时的表面氧化膜进行了分析，探讨了表面氧化膜的组成与结构。

Surface oxidation film of Mg alloy casting in dry graphite silica sand mold was analyzed by XPS . The constituent and structure of surface oxidation film were discussed .

文章在论述镁合金加工行业特点的基础上，结合ASP理念与技术，介绍了所开发的面向ASP服务的镁合金加工行业的工艺信息系统平台及关键技术。

This paper describes the characteristics of magnesium alloy machining trade , an ASP-oriented process in-formation system platform for magnesium alloy machining trade and key technique are described in detail .

AZ31镁合金板热拉深成形工艺研究

Research on the Thermal Deep-Drawing Process of ( AZ31 ) Magnesium Alloy Sheets

铜介绍了镁合金表面镀Ni-P的研究现状及发展趋势，镁合金表面采用Ni-P镀是一种很有应用前景的表面处理工艺。

The research situation and development direction of Ni-P plating on magnesium alloy were dis-cussed . It showed the Ni-P plating has high applies perspective .

由于镁合金不填丝的TIG焊接接头强度低，焊缝表面成型不好，所以，镁合金的填丝TIG焊接方法不可避免。

Because TIG welded joints without filler wire always hold low strength and poor formation , tungsten inert gas welding process with filler wire is inevitable .

Nd的最佳含量则为0.5wt%，此时AZ61镁合金的高温力学性能最佳；

While the best content for Nd is 0.5 % , at where the high-temperature mechanical properties are the best .

当镁合金替换原有的车用金属材料后，必将影响整车的NVH性能。

If original automotive metal materials are replaced by magnesium alloy , the vehicle NVH performance must be affected .

Mg-Al-Zn（RE）镁合金轧制变形行为及强化机制

Rolling Deformation and Strengthening Mechanism of Mg-Al-Zn ( RE ) Magnesium Alloys

AZ31B镁合金薄板经单向多道次弯曲及退火后的组织与性能

Structure and Properties of Magnesium Alloy Sheets Undergoing Repeatedly Unidirectional Bending and Annealing

变形镁合金AZ31B的激光焊接工艺研究

Study of YAG Laser welding process on wrought magnesium

建立了AZ31镁合金板材流变行为和冲压性能与变形条件之间的对应关系。

( 6 ) The relationship among the deforming behavior , drawability and deforming conditions were studied .

分析了镁合金ECAP加工技术的试验和模拟方案。

Experiment of Democratic Village Routine in the Procession of Commandeering Land Routine of experiment and modeling for ECAP of magnesium alloys was schemed .

通过有限差分法，利用Visualc++6.0建立直接水冷法（DC）AZ31镁合金连铸过程的数学模型，该模型可预测铸锭以及底模的温度分布。

A mathematical model of DC casting process for magnesium billets was developed to predict the temperature in the billet and dummy block using Microsoft Visual C + + 6.0 and finite difference method ( FDM ) .

研究发现只要选用合适的工艺条件，AZ31镁合金可以进行大压下率轧制。

It is found that AZ31 Magnesium alloy could be rolled with heavy reduction rate if appropriate processing parameters are chosen .

利用AutoCAD为开发平台，以其内嵌的VBA为开发工具，采用ACCESS及SqlServer建立数据库及作为数据库管理工具，建立了结合数据库的镁合金挤压管材模具参数化设计系统。

Take advantage of AutoCAD as developing platform and VBA tool setting in AutoCAD platform , make use of ACCESS and SQL Server as data base , the author established AutoCAD parameter design system for magnesium alloy hot extruded tube mould .