附着层

然后建立含缺陷多层级蜂窝的有限元模型，最后确定需要讨论的附着层材料和几何参数。

Then , the imperfect honeycombs ' finite element models are established . At last , the material and geometric parameters of the adhesion layer are determined .

采取正确的过滤和沉淀措施后阳极黑色附着层对镍锰合金电铸过程不会产生明显的影响。

After proper filtration and precipitation , the loose black layer had little effect on the electroforming process of the Ni-Mn alloy .

本文中从单一材料的导热系数测定公式着手，得出了带附着层的复合材料导热系数的计算公式，并通过实验进行了验证。

On the basis of determining equation of the thermal coefficient of a single material , the calculating equation of the thermal coefficient of the composite with the adhesional layer is drawn , and it is verified by experiments .

对于新换热管而言，污垢的生长首先是基层的形成，然后是难以清除的附着层的形成；对于除污后的换热管，污垢再次生长过程主要是附着层的形成。

During the late exponential asym-ptotic growth characteristics reflect the fouling layer forming process . To the new heat exchange tube , first fouling growth is the basic form , and it is difficult to remove the adhesive layer formation .

挂膜结束时，纤维球串体周围生长了一层厚厚的附着层污泥，底部悬浮相污泥絮体大且蓬松，出水澄清透明；

At the end of membrane-hanging , a thick layer of attachment sludge has grown up around the fiber-ball string bodies and the sludge flocs in suspended phase at the bottom were big and fluffy , while the effluent water was clear and transparent .

选用具有高度亲水性的水溶性聚合物&聚乙烯醇作为改性材料对己有的疏水性微滤膜采用表面涂覆法进行改性，在表面附着一层亲水性PVA水凝胶超薄层制得了聚乙烯醇复合膜。

The PVA with highly hydrophilic character , are used as microfilter modified membrane materials to modify hydrophobic membranes by coating . The PVA thin film composite membranes are prepared with PVA hydrogel layer form on the surface of substrate membranes .

再附着剪切层中的大涡结构

Large Eddy Structure in Shear Layer With Reattachment

早期层合智能结构的研究主要集中在传感层和致动层都附着在层合智能结构的表面。

Early researches of smart structures were mainly concentrated in adhesive sensor and actuator layers .

附面层迁移不仅包括附着涡层的迁移，而且包括自由涡层的迁移，而自由涡层的迁移主要受分离范围和分离形态的影响。

Boundary layer movement consists of the movement of surface eddy layers and the movement of free eddy layers which is affected by the separation range and the separation type .

镀锌板是在普通钢板的表面附着一层锌层，使其具有良好的防腐蚀性能。现在已经越来越多的应用在汽车、建筑、家电等行业。

Zinc coating in the surface of ordinary sheet called zinc-coated sheet , it has good corrosion resistance and was used in the automotive , construction , household appliances industry .

本实用新型的水流为下进上出式，污垢附着过滤层下端，故极易冲洗。

Water flows through the utility model from bottom to top , and dirt is attached to the lower end of the filter layer , so that the utility model is easy to wash .

在此基础上，用聚乙烯吡咯烷酮（PVP）做还原剂，还原银氨溶液，在室温条件下将纳米银颗粒附着在碳层的表面，反应条件温和。

On this basis , silver ammonia solution was reduced by polyvinylpyrrolidone ( PVP ) at room temperature , which made silver particles attached to the surface of the carbon layer .

基体（1）的外表面上也附着有一层光触媒（3）。

The outer surface of the basic body ( 1 ) is also adhered with a layer of photocatalysts ( 3 ) .

通过对比各种工况的阻尼车轮加速度-频率响应曲线可知，对于阻尼车轮而言，两面都附着约束阻尼层的减振效果要远好于单面附着阻尼层的减振效果，且附着面积越大，其效果越好。

The comparison between acceleration-frequency response curve of different conditions shows that for damped wheel , the effect on reducing vibration of damping layer attached to two sides is much better than to one side , and the more the attachment size , the better the effect .

实验结果表明，桐油在复合肥料颗粒表面经热固化后形成连续和附着良好的包膜层，包膜率为10.1%的桐油包膜复合肥料的80%养分释放时间可达到27d。

The experimental results show that tung oil on the surface of the compound fertilizer granules after heat solidification forms a continuous envelope with good adherence , and tung oil-coated compound fertilizers with a coating rate of 10.1 % have 80 % of their nutrients released in 27 days .

其次江水在换热器内流动换热过程中泥沙会沉淀和附着，形成垢层。

Secondly , sediment of water will precipitate and adhere to form a scale layer while flowing .

在拍摄时，剧组成员改进了原本用于测试的系统，打光继续采用主要从车的垂直上方的平衡摄影架照射下来的方式，看着就像车子顶部附着上了一层光晕。

For the shoot , the filmmakers refined the system they had utilized for the test and continued to light primarily from the roof-mounted speed-rail rig , which sat like a halo atop the car .

分别对轴表面附着和不附着非晶态合金层进行了动态转矩测量，对比分析了两种情况下的测量精度和灵敏度。

By experiments , the effects of the gap between the sensor probe and the shaft surface on sensor outputs were analyzed , and the best gap rang was got .