不合格品

  • 网络nonconforming;Unqualified Product;defective;defects;Reject
不合格品不合格品
  1. 文末,利用扩展的活动图表达了质量管理中一个典型的过程&不合格品的控制过程。第三章详细介绍了选课子系统的基于UML的设计蓝图。

    The extended UML activity diagram is used to illustrate the defective product control process which is a typical process of quality management .

  2. 进货检验、最终检验以及顾客退回的不合格品的评审,由质量部组织相关部门评审,做好记录。

    Quality Dept. is responsible for organizing relevant departments to review and record incoming inspections , final inspections and defective products returned by the customers .

  3. 此外,利用不合格品率(p)控制图对印后装订工序的不合格品进行了分析和监控。

    In addition , p control chart is used to analyze and control the unqualified rate of the binding .

  4. 最后给出了来料不合格品控制流程在当前设计的Web平台上运行实例。

    By applying the system , the paper gives the running instance of nonconforming product control process on the Web platform in the end .

  5. 开展降损活动控制CATV用声表面波滤波器不合格品率

    Increasing Qualified Product Ratio of SAW Filters For CATV hy TQC Activity

  6. 介绍计件值工序中常用的Pn-控制图,阐明如何估计不合格品率p及合理选择抽样个数n。

    This article introduces Pn-control chart commonly applied in count-basis process , and illustrates how to estimate the rate of preference for rejection P n and reasonable choice sampling number n.

  7. qa同事发出扣留信息,同时在不合格品上贴扣留单。

    QA colleagues send the detainment information , and paste the detainment bill on the non-conforming products .

  8. 本文针对微电路生产的实际特点,在工艺不合格品率为PPM水平时,讨论了等效工序能力指数的概念和计算方法。

    A new concept of the Equivalent Process Capability Index and its estimating method are provided at PPM level .

  9. 不合格品的处理应当考虑并符合ccp策划中纠偏行动的要求。

    The handling of non-conforming products should be considered and should comply with the requirement on the corrective action in CCP planning .

  10. qc在线检测发现不合格品时,立即扣留成品,查明原因,通知生产及时调整。

    When finding non-conforming products in the on-line test , QC detains immediately the finished products , identifies the cause and informs production department to make timely adjustments .

  11. 三台1200m3引进乙烯球罐因球壳板的曲率超差判为不合格品而废置,后对球壳板进行修复重新安装再利用。

    As the curvature of shell steel plate exceeding the specified value , three 1200m 3 imported ethylene spherical tanks were judged to unqualified product and put aside as useless . After repairing and reinstalling , the shell steel plate were reused .

  12. 不合格品进行控制,供应商质量改进及跟踪;

    Quality control on nonconformity parts , supplier quality improvement tracing .

  13. 应按《状态标识控制程序》标识不合格品。

    Non-conforming products should be identified as per Status Identification Control Procedure .

  14. 发现不合格品时,要做好标识,隔离存放。

    Non-conforming products should be identified and segregated when found .

  15. 在机械零件的切削加工和检验中,可能出现伪不合格品。

    There may be pseudo_unqualified products during the course of mechanical cutting .

  16. 包钢大中修工程不合格品的控制

    Control of nonconforming product in major and intermediate overhaul at Baotou Steel

  17. 供应商不合格品信息的反馈,跟踪及处理。

    Defect parts information feedback to supplier and follow up .

  18. 进货中的不合格品须隔离并加上标识以防止进一步使用。

    Incoming non-conforming materials are segregated and separately identified to prevent inadvertent use .

  19. 制造业企业不合格品的管理

    Enterprise of the Manufacturing Industry to Manage the Reject

  20. 批量生产中不合格品返修物流规划

    Reverse Logistics Planning of Un-standard Products in Mass Production

  21. 在控制不合格品率前提下的控制界限的确定

    Determination of Control Range under the Presupposition of Controlling Rate of Unqualified Products

  22. 不合格品,次品:一件不规则的东西,如商品。

    One , such as an item of merchandise , that is irregular .

  23. 任何返工后的不合格品均须重新检查。

    Any reworked non-conforming products must go through the re-inspection processes after rework .

  24. 检验员负责监督不合格品的处置。

    The inspectors are engaged to supervise the disposition of the nonconforming items .

  25. 应以对待不合格品的类似方法控制过期产品。

    Obsolete product shall be controlled in a similar manner to nonconforming product .

  26. 谈谈不合格品的控制

    A Discussion To The Control Of nonconforming Product

  27. 零不合格品质量控制图研究

    Research on the Control Chart of Zero-Nonconformity Production

  28. 可变抽样区间不合格品数控制图

    Defective unit control chart with variable sampling intervals

  29. 关于生产过程中不合格品控制的探讨

    Study on Non-conformity Product Control during Manufacturing Process

  30. 这样当出现不合格品时,就可以找到对应的负责人。

    This is to identify who is responsible for rejects found down the line .