过盈配合

机械零件过盈配合计算

Calculation of interference fit for machine parts

基于可靠性优化技术的计算和选择过盈配合的新方法

New method to calculate and choose interference fit based on the reliability and Optimization Technology

基于AutoCAD的过盈配合计算机辅助设计系统

The CAD System of Tight Fitting Based on AutoCAD

利用大型有限元软件ANSYS研究了孔轴过盈配合接触面的应力分布和应力集中情况。

The contact stress distribution and stress concentration are studied used the finite element analysis software ANSYS .

HSK刀柄锥面过盈配合的可靠性分析

Reliability Analysis for Tapered Interference Joint of HSK Toolholder

改进了传统的实心轴为空心轴使得设备重量减轻，并且利用ANSYS软件对空心轴的过盈配合进行了有限元分析。

The traditional solid axis is improved to become hollow to lighten the machine 's weight and interference joint of hollow axis has been the finite element method analysed by the ANSYS .

本文以标准直齿圆柱齿轮和轴的过盈配合为例，说明了ANSYS有限元分析软件在过盈配合联接安全核算中是可以适用的。

Following the example of surplus joint of standard straight cylinder gear and axle , the article has explained that ANSYS Finite Element Analysis software can be applied to stress analysis of the surplus joint .

以ANSYS为平台，利用有限元方法对矿用牙轮钻头牙轮齿孔过盈配合进行了有限元计算，并分析了牙齿和齿孔应力分布规律及过盈量对其的影响。

The over-fixation of mine-used rotary drill bit tooth hole was calculated by the finite element method on ANSYS , also analyzed the distribution laws of tooth hole and tooth stress field and influence of the over-fixation .

径向过盈配合0.1mm，轴向拉伸载荷336MPa。

Radial interference fit ( 0.1 mm ) - 336 MPa axile tensile load .

本文利用各向异性体平面弹性理论中的复势方法，以Faber级数为工具，导出层板多孔/弹性核过盈配合在钉载作用下的级数解。

Uses Faber series expansion and the complex potential method in the plane theory of elasticity-of an anisotropic body . The series solution of composite laminates with multiple interference fitting load-pins is obtained .

根据该力学模型，讨论了四种不同载荷，即，无过盈配合，套管轴向拉伸载荷50MPa；

Based on the dynamic mode , this paper presents the discussion on four different loads , that is , non-interference fit-50 MPa tensile load ;

另外，对Bridgman密封进行了改进，用来实现柱塞密封；引线密封则采用O形圈以及锥面配合来实现；端面密封采用柱面过盈配合并用锥面作为挡圈压住密封圈实现。

Piston seal using the improved Bridgman seal and lead seal used the o-ring and cone to realize ; To realize the end face sealing , the cylinder interference fitted was applied as well as using cone as block circle to press the seal ring .

压气机过盈配合的弹塑性有摩擦接触的研究

Study on elastoplastic frictional contact problem in interference fits of compressors

采取过盈配合的目的是控制飞轮临界转速。

Interference fits serve to control critical speeds of the rotors .

过盈配合受载荷轴对称体的有限元法分析

FEM Analysis on interference fit Ted symmetrical body of rotation

论以无机粘接取代过盈配合

Touch on replacement of shrink fit in tolerance system by inorganic bonding

无摩擦情况过盈配合螺栓的有限元分析

Analysis of friction & free interference fit bolt using finite element method

过盈配合组合轴对称体结构分析有限元程序开发

Interference Fit Axisymmetric Entity Finite Element Structure Analysis Program Development

液压安装锥度过盈配合在机械压力机中的作用

Application of HydrauLic Interference Fit of Cone Surface Connection to Mechanical Press

齿轮组合圆柱面过盈配合联接设计分析

Analysis of the Interference Fit of Cylindrical Surface in Combination With Gear

塑性状态过盈配合联接的承载能力计算

The calculation of bearing capacity of interference fit joint in plastic deformation

提高过盈配合组件承载能力的研究

The Study on Increasing the Load Carrying Capacity of Interference Fitted Assemblies

过盈配合另件的应力分析

A Stress , Analysis For The Part With Forced Fit

基于有限元法的过盈配合接触特性分析

Study on Contact Characteristics of Interference Fit based on FEM

过盈配合接触电阻测试法的探讨

Approach on the contact resistance test method for interference fit

有限圆板内孔冷挤压和过盈配合问题的弹塑性分析

Elastoplastic analysis of a finite sheet with an interference-fitted and coldworked hole

机车轮对过盈配合温差法装配的有限元模拟

FE Simulations of Interference Fit Joints of Wheel and Shaft in Locomotive

钉载作用下层板多孔过盈配合分析

Analysis of Composite Laminate with Multiple Interference Fitting Load-Pins

基于有限元的高速旋转主轴过盈配合研究

FEM-Based Study on Interference Fits in High-Speed Rotatory Spindles

船舶尾轴机械密封镶嵌式动环过盈配合分析

The Interference Fit Analysis of Mosaic-type Rotating Ring on Stern Shaft Mechanical Seal