铸锭

Nd-Fe-B系铸锭显微结构的研究

Study on the Microstructure of Nd-Fe-B Cast Ingot

计算了温度场改变前后铸锭不同部位凝固组织中的析出相含量，并讨论了析出相含量变化的成因。

The content of precipitated phase in different parts of cast ingot pre-and post temperature change was calculated .

沸腾钢在铸锭前不脱氧或轻度脱氧

In the case of rimming steel , no or some deoxidation is carried out before casting .

基于微分先行PID算法的铸锭炉温控系统

Temperature Control System Based on Differential ahead PID Algorithm of Polysilicon Ingot Furnace

Ni基合金电渣重熔铸锭中孔洞形成的原因分析

Formation of Central Hollow Inside Ni-base Alloy Electroslag Remelting Ingot

Al－4%CU铸锭凝固中自由等轴晶的迁移行为及对宏观偏析的影响

Movement Behavior of Equiaxial Dendrites in Solidifying Al-4 % Cu Ingots and Influence on Macrosegregation Freedom

牙科铸造用Co－Cr合金在真空感应炉中进行熔配.浇成小铸锭。

A dental casting Co-Cr alloy was melted by vaccum induction furnace and casted into little ingot .

Ca、Sr、Sb对镁铸锭组织的细化作用

Refinement Effect of Ca 、 Sr 、 Sb Addition on Structure of As-cast Mg Ingot

PLC与触摸屏电铅铸锭机组的电控系统设计与实现

The design and implementation of electrical-controlling system in electricity lead ingot casting unit based on the PLC and touch screen

用电子探针、X射线衍射仪等设备研究了商用铌铁铸锭中的相。

Used Equipment Plant Performance The phases in commercial Nb-Fe alloy ingot were investigated by X-ray diffractometer and electron probe microanalyser .

介绍了SiC颗粒增强铸造铝基复合材料的铸锭重熔、除气和铸造过程的特征。

Remelting , degassing and casting processes of SiC particle reinforced aluminum composites were studied and analyzed .

随着Cr、Mn含量增加，铸锭晶粒向枝晶化、粗大化方向发展。

With increasing content of Cr and Mn in the alloy , the grains become coarse and dendritic .

机械搅拌对Al及Al-Cu合金铸锭组织和宏观偏析的影响

Effect of Mechanical Stirring on the Structure and Macrosegregation of Al and Al-Cu Alloys

LD2、LD（31）合金铸锭均匀化及过烧研究

Research about homogenizing and Overburning of ld_2 and ld_ ( 31 ) alloy ingot

结果表明，复合材料铸锭中，SiC颗粒分布均匀；材料的硬度随SiC颗粒体积含量的增加而增加；

The Results of the hardness test showed the composites ' hardness increased with the increasing volume fraction of SiC particles .

Nd-Fe-B铸锭中α-Fe相含量的确定

Determination of α - Fe Phase Content in Nd-Fe-B Cast Ingots

在高温纯铁熔体中加入平均尺寸为2.7μm的TiN颗粒，熔炼后得到铸锭试样。

The ingot specimen was obtained by melting industrial pure iron in which TiN particle with 2.7 μ m size was added .

废防震泡沫塑料（EPS）在粘合剂中的应用研究SiC颗粒自增粘熔体发泡法制备泡沫铝铸锭的组织及其特征分析

The Structure and Its Characteristics Analysis of Aluminum Foam Ingot Fabricated by Molten Frothing Process Using SiC Particles Adhered Melt

用传统的合金铸锭工业生产高性能Nd-Fe-B烧结磁体的方法

Method of Mass-producing High Performance Sintered Nd-Fe-B Magnets From a Conventional Alloying Ingot

铸造热变形Nd-Fe-B永磁合金铸锭组织的研究

Study on microstructure of Nd-Fe-B ingot for hot-deformed cast Nd-Fe-B permanent magnetic alloys

Nd-Fe-B鳞片铸锭的显微组织与厚度及合金成分的关系

Study on relationship between microstructure and thickness and composition of Nd-Fe-B strip cast

同时本文还提出了适合铸锭凝固过程的柱状晶向等轴晶转变（CET）判据。

A columnar-to-equiaxed transition ( CET ) criterion is developed for the case of solidification of ingots .

Mg-Li基复合材料铸锭中的孔隙控制工艺

Porosity controlling process of Mg-Li matrix composites ingot casting

ICP-AES测定铝锭中八种杂质元素浅析铝合金铸锭均匀化退火表面起泡原因

Simultaneous Determination of 8 Impurity Elements in Aluminium Ingot by ICP-AES Analysis to the Bubble Formed on Surface of Aluminium Ingot During Homogenization Annealing

铸锭组织的不均匀性对烧结Nd-Fe-B磁体的制粉工艺及磁性能的影响

Influence of the Inhomogenous Microstructures of Nd-Fe-B Ingot on the Powdering Process of Sintered Magnets and Their Magnetic Properties

Cu-Cr-Zr合金铸锭铸造缺陷产生原因与防止措施

Defects Analyzing And Prevention of Cu-Cr-Zr Alloy Ingots

Mg-Li合金熔炼反应的热力学分析及铸锭显微组织

Thermodynamic Analysis of Chemical Reaction in Melting Process of Mg-Li Alloy and Microstructure of Ingot

Zr-4合金铸锭化学成分的控制

Chemical composition control of Zr-4 alloy ingot

本文采用铝熔体热爆合成法，以Al粉、Ti粉、C粉为原料合成制备20kg新型Al-Ti-C细化合金铸锭；

The new pattern Al-Ti-C grain refining alloys had been prepared by thermal explosion method using Ah Ti and C powder in aluminum liquid in this thesis .

熔体超声场处理对Al-Pb合金铸锭偏析及性能的影响

Effect of Melt Ultrasonic Field Treatment on segregation and property of Al-Pb Alloy Ingots