挤压成型

模塑和挤压成型的聚酰胺（pa）材料第1部分：命名

Polyamide ( pa ) moulding and extrusion materials - part 1 : designation

初步研究了工程塑料尼龙（PA）的挤压成型工艺。

It preliminarily studied the extrusion molding technique of engineering plastics ( PA ) .

B级钢轴箱体半固态挤压成型模具的研究

Study on Die of Axle Box Body of B Grade Steel by Semi-Solid Squeeze Forming

基于inventor食品挤压成型机中螺杆的三维参数化造型设计

3D Parameterized Modeling Design of the Food Extruder Screw Based on Inventor

介绍了聚四氟乙烯（PTFE）分散树脂推压成型（也称糊膏挤压成型）制品的工艺技术。

The technology of PTFE dispersion resin press mould ( also called paste extrusion moulding ) is introduced .

SBP挤压成型工艺的应用研究

Study on the Application of SBP Extrution Forming Technology

以α-Al2O3粉末为骨料，以聚乙烯醇（PVA）作粘接剂和成孔剂，采用塑性挤压成型技术和固态粒子烧结法制备氧化铝多孔陶瓷支撑体。

A porous ceramic support comprising alumina and PVA ( polyvinyl alcohol ) was prepared by extrusion and solid sintering .

主要用于PVC管、板、片、膜、型材、造粒等塑料制品的塑化和挤压成型。

It is mainly used in plasticizing , extruding and forming PVC pipe , plate , sheet , film , profile , and granulator etc.

通过B级钢轴箱体半固态挤压成型的大量试验，得出其模具的主要失效形式为塑性变形、热疲劳裂纹和热熔蚀。

The main failure forms , such as thermal fatigue crack and thermal ablation of die of axle box body by semi-solid squeezing forming of B grade steel were presented based on lots of experiments .

本文则通过运用ANSYS有限元分析软件，根据挤压成型金属波纹管机械密封的使用工况选取参数进行优化分析，最终获得最为优化的结构尺寸。

The most optimized structure size is obtained by ANSYS finite element analysis software according to selecting the operating conditions parameters of analysis for metal bellows mechanical seals by extruded forming .

介绍了几种常见的P形管的规格及技术要求、孔型的计算机辅助设计、生产P形管的两种成型方式，着重介绍了由圆管通过挤压成型为P形管的成型原理。

It presents a few common sizes and technical requirements of P shape pipes and produces P shape pipes by adopting two forming modes with pass design of CAD . It emphasizes to present the forming principle of P shape pipe from round pipe by extruding forming .

采用JQT型轻质隔墙板挤压成型机生产陶粒混凝土空心隔墙板的体会和建议

Suggestions on producing hollow concrete ceramisite slab by JQT press

但厚度大于4mm的T型接头由于设备局限很难通过挤压成型，而传统的T型接头角焊又往往受结构空间所限无法实施。

Due to equipment limitation , it is difficult to extrude that thickness of T-joint is greater than 4mm . The traditional T-joint fillet weld can not be implementing because of limitation of the structure .

结果表明，经扩散退火处理的ZA-27铸造合金适用于冷挤压成型方法，制件的成品率为100%。

The result of the investigation shows that ZA27 alloy by diffusion annealing is suited for cold extrusion processing method , the proportion of finished product of the element was100 % .

挤压成型预应力混凝土空心板生产技术操作规程

Operation specification for extrusion technique of prestressed concrete hollow cored slab

农作物秸秆挤压成型育苗容器的研究进展

Review of Research on the Corp Straw - extruded Seedling Container

锌基轴承合金的液-固态挤压成型工艺

Liquid solid Extrusion of Shaped Tubes of Zinc base Bearing Alloy

连续挤压成型包覆机挤压轮用钢的热处理工艺

Heat treatment of steel for extrusion wheel of CONFORM clad machine

钢筋混凝土空心板行模挤压成型机设计计算

The calculation of reinforced concrete hollow core slab line-model extrusion machine design

125型摩托车铝合金车轮的液态挤压成型

Liguid Extrusion Forming for 125 Type Motorcycle Aluminium Alloy Wheel

三种挤压成型的改性双基推进剂的安全特性

Safety Characteristics of Three Extruded Composite Modified Double Base Propellants

海底土中挤压成型混凝土桩基技术研究

Study on Concrete Pile of Compaction Forming in Subsea Soil

挤压成型玉米醇溶蛋白膜的制备及性质研究

Studies on the Process and Properties of Zein Film Made by Extrusion

以天然沸石为原料，采用挤压成型的方法，制备出多孔陶瓷分离膜管。

Porous ceramic tubes have been fabricated by extrusion from natural zeolite .

塑性挤压成型90氧化铝陶瓷工艺研究

Study on Preparation Process of 90 Alumina Ceramics by Plastic Extrusion Forming

小六角火花塞壳体单冲冷挤压成型工艺

Small Hexagon Spark Plug Shell Single-Punch Cold Forming Technology

粉末挤压成型的有限元数值模拟

Data Simulation of Finite Element in Powder Extruding Shaping

高温改质煤沥青挤压成型工艺参数的研究

Study of parameters in extruding procedure with high softening-point modified pitch as binder

螺旋式稻壳挤压成型机设计

The Design of Spiral Extrusion-shaping Machine for Rice Hull

设计的往复活塞双向挤压成型机构具有创新性。

A novel two way briquetting structure with two reciprocating pistons was designed .