挤压法

用AN＿1／WS型铆钉机加工由挤压法和包套法制备Pd／Ag52纤维复铜触点，并进行微观结构剖析。

The Pd / Ag fiber-copper composite contact was prepared by the riveting machine of AN_1 / WS type with the methods of squeeze-press and casing pipe .

结果表明：与传统的挤压法相比较，铸轧法生产ACR铜管工艺技术具有先进性、经济性和可行性。

The results showed that the cast-roll process produced ACR copper tubes was more advanced , economical and realizable comparing with the extrusion process .

采用超音速气体雾化法制备快速凝固高硅铝合金粉末，通过热挤压法对雾化合金粉末进行固结成形，并利用T6处理工艺对挤压态合金进行热处理。

The powder is prepared by ultrasonic gas atomization process , consolidated by hot extrusion and T6 temp of the alloy is carried out after extrusion .

可能是治疗DOMS更适合采用与皮肤接触面积大的手法，同时也说明挤压法和抖法更有利于缓解DOMS。

DOMS may be more suitable for the treatment of skin contact with a large area of practices , but also squeezing and buffeting that law is more conducive to alleviate DOMS .

简要介绍等通道转角挤压法（ECAE）的基本原理及通过该方法得到的有效应变量的主要影响因素。

The mechanism of Equal Channel Angular Extrusion ( ECAE ) is briefly introduced , the influential factors on effect strain obtained by severe plastic deformation are also presented .

采用挤压法试验生产的ZA12锌铝合金轴套，制品表面光洁、无裂纹；显微组织和机械性能均优于铸件；

The sleeve , which is produced by extruding and is made from ZA12 Zn-Al alloy , has high surface finish and no crack on its surface .

同时本文采用挤压法半定量地测定了纤维&基体结合键强度，从而揭示了FCVI纤维涂层提高材料断裂韧性的纤维拨出机理。

Also , fiber-matrix bond strength has been semi-quantitatively evaluated by using indentation methods , and so the fiber pull-oot mechanism for increasing fracture toughness has been presented .

本文结合开展的试验，重点介绍了堆积法和挤压法。

With experiments , the stacking-capillary method and extruded method areintroduced .

挤压法生产焦糖色素的探讨

Discussion on the preparation of caramel pigment by extrusion SPLIT-PHASE METHOD

石灰挤压法在废白土处理装置中的应用

Utility of lime squeezing method in the waste clay treatment plant

挤压法生产玉米面条的工艺探讨

A Discussion on the Extruding Technology for Producing Noodle form Corn

热挤压法生产紫铜电脑散热片的研究

Research on producing pure copper computer thermal fin with hot extrusion method

挤压法生产铝包稀土、钙复合丝

The aluminium clad composite wire containing calcium and rare-earths produced by extrusion

挤压法处理木浆厂筛渣

Extruding Process for Coarse Rejects Treatment of the Pulp Mill

拉拔退火法与连续挤压法铜扁线的组织分析

Microstructure of Copper Strip Produced by Drawing - anneal and Continuous Extrusion

采用热挤压法成型制备出卤化银多晶光纤。

The silver halide fibers were made by means of hot extrusion .

挤压法生产可溶性燕麦纤维的研究

Study on the Extruding Production Method of Soluble Oats Fiber

本文对传统的索氏萃取法与新的试验法&快速挤压法进行对比分析。

This article compared the traditional soxhlet extraction with the new rapid extrusion .

用径向挤压法制造大法兰锻件的研究

Study of Big Flanged Forgings Stamping by Cross Extrusion

挤压法生产淀粉软糖工艺的研究

Technology Studies on Starch Soft Candy with Extrusion

挤压法重质纯碱装置的工艺改进

Process Improvement of Extruding Dense Soda Ash Plant

熔融挤压法在工业药剂学上的应用

Application of Hot-melt Extrusion Technology in Pharmaceutical Fields

球体挤压法精加工内孔

Finishing Machining Hole with Ball 's Press Method

挤压法治疗断指再植术后静脉危象的实验和临床应用

Experiment and clinical application of squeezing technique in venous crisis after replantation of finger

并且在改进工艺的基础上，采用中心抽真空挤压法对其进行了制备。

Furthermore , it is fabricated with the improved extrusion method of the center vacuumized .

用挤压法提高豆渣可溶性膳食纤维含量的研究

A Study on te Use of Extrusion for Raising the SDF Content in Soybean Dregs

连续挤压法介绍

An Introduction to Continuous Extrusion Process

对铜盘管的两种生产工艺&铸轧法和挤压法进行了比较。

The casting-rolling ( CR ) and extrusion procedure for processing copper coil tube have been compared .

除正常对照组外，其它各组均采用颈总动脉挤压法建立血管内膜增生模型。

Excluding the control group , the intima hyperplasia models were founded in the other two clusters .

连续挤压法的工艺原理及其优越性，分析研究了影响铜线连续挤压加工的各种工艺因素。

The technologic factors affected on the continuous extrusion production of copper lines were analyzed and researched .