泄漏率

  • 网络leakage;Leakage Rate;Leak rate
泄漏率泄漏率
  1. 基于主蒸汽管道中16N核素监测的蒸汽发生器泄漏率监测方法,目前已成为蒸汽发生器泄漏监测的主导方法。

    The method of through monitoring 16N activities in the main steam pipe to get the leak rate of steam generator , now is the main way of steam generator leak rate monitoring .

  2. 蒸汽发生器泄漏率监测

    Steam Generator Leak Rate Monitoring System

  3. SDH系统中去同步器泄漏率算法的研究

    The Research of Bit-Leaking Calculation on Desynchronization in SDH System

  4. 在理论上计算了两种真空封装外壳泄漏率以及真空度的保持时间。通过理论计算与实际测量给出了真空封装的MEMS器件的理论寿命。

    The theoretical calculation and measurement provide the theoretical life of MEMS devices after vacuum packaging .

  5. 在320℃、12.2MPa下,水的泄漏率为0.3g/min时,5s内发出报警。

    When the leakage rate of water at320 ℃ and 12 . 2 MPa is 0.3g / min , the alarm signal will sent out within 5s .

  6. 对600MW直接空冷机组的空气泄漏率应以不大于30Pa/min为宜。

    The air leakage flow rate to 600 MW direct dry cooling units should not be greater than 30 Pa / min.

  7. 经氦检漏试验,热电偶贯穿件泄漏率小于1×10-7Pa·m3/s。

    For our thermocouple penetration assemblies , the leakage of helium gas is less than 1 × 10 - 7Pa · m3 / s.

  8. 邯郸热电厂2台200MW机组真空系统泄漏率较大,直接影响着机组的真空状况。

    There exist unacceptable leakage in the vacuum systems of two 200 MW units in Handan cogeneration Power Plant , which directly impact the vacuum condition .

  9. 论述了STM-1的解映射及去同步以获得2Mbit/s异步信号的实现方案,并提出了减小指针调整引起的抖动的自适应比特泄漏率算法。

    The realization project to extract 2 Mbit / s signal from STM-1 is discussed in this paper . The arithmetic of adaptive bit leak rate to reduce the pointer justification jitter is put forward .

  10. 在考虑磨损引起端面表面形貌变化的基础上,引入分形理论分析了弹簧比压对平衡型机械密封泄漏率和端面摩擦特性的影响,并针对GY-70平衡型机械密封进行了试验研究。

    While the fact that abrasion leads to change of surface topography was taken into consideration , the influence of spring pressure on both leakage rate and friction characteristic of balanced mechanical seals was investigated by fractal theory . Several GY-70 type balanced mechanical seals were tested .

  11. 最小泄漏率为10-11Pam3/s。

    Rate of leakage is 10 - 11 Pam 3 / S.

  12. 长输管线气体泄漏率的计算方法研究

    Estimation of accidental gas release flow rate in long transmission pipelines

  13. 防放射性微粒呼吸器泄漏率测试装置

    A device for measuring leakage rate of respirators against radioactive particulates

  14. 长输管道稳态气体泄漏率的计算

    Estimation of Steady State Gas Release Flow Rate in Long Distance Pipeline

  15. 空间O型圈密封泄漏率实验研究

    Experimental Reasearch on leakage rate of space seal with O-ring

  16. 原子氧对O型圈泄漏率的影响

    Effect of Atomic Oxygen on Leakage Rate of O-Ring

  17. 应在最大允许工作压力下测量泄漏率。

    The leak ratio shall be measured at mawp .

  18. 压水堆核电厂一回路冷却剂泄漏率计算的优化燃烧装置内部漏泄率

    Optimization of Leakage Calculation in RCP System of PWR

  19. 管道穿透裂纹泄漏率计算程序

    Calculation Program for Leak-rate of Pipe Penetrated - crack

  20. 原子氧及紫外线对O形圈泄漏率影响的研究

    The Study of the Effect of O-Ring Exposure to Atomic Oxygen and Ultraviolet

  21. 以逐步隔离法为基础的系统泄漏率试验经济性回收分析

    Economic Benefit Recovery Analysis of System Leakage Ratio Test Based on Gradually Insulation Method

  22. 研究了泄漏率、耦合面径向力随时间的变化情况;

    The time-dependent change of leakage rate and radial force of interface was analyzed .

  23. 位置偏心对斯特林制冷机回热器泄漏率的影响

    Effect of the Eccentric Position on the Leakage of the Clearance Seal in Stirling Refrigerator

  24. 螺栓法兰连接系统泄漏率计算

    Leakage rate calculation of bolted flange connections

  25. 反应堆安全壳的局部泄漏率试验

    Local Leakage Rate Testing for Reactor Containment

  26. 气雾剂的平均年泄漏率为3.03%,每瓶泄漏率均小于5%。

    The average leaking rate was 3.03 % per year which was less than 5 % .

  27. 研究表明,可通过调节闭合力可实现对泄漏率的控制;

    The result shows that the leakage rate can be controlled by adjusting the closing force .

  28. 也可用起始泄漏率的30%近似代替总平均泄漏率。

    The total average rate of released gas could be substituted by 30 percent of initial released rate .

  29. 相关标准对金属密封副止回阀密封试验泄漏率的规定及分析

    Measure and analysis about the leakage rate in sealing test for metal-seated check valve covered in GB standard

  30. 采用互锁搭扣结构,伸缩性好,泄漏率低,能承受一定扭矩。

    Hasp using interlocking structure , flexibility , low rate of leakage , can withstand a certain torque .