镀层

改变置砂方式，采用了悬浮置砂法，可提高齿面磨粒的均匀性，并在电镀后增加真空热扩散工艺，增强了镀层与基体的结合力。

Using suspending method to putting abrasives may better the uniform of abrasives and adding thermal diffusion in vacuum at high temperature after electroplating , the binding force between cladding material and matrix is improved evidently .

检测片状电阻器镀层厚度的金相制样法

Metallographic specimen preparing method for measuring the cladding material ′ s thickness

水龙头外表为铬镀层

Water faucets shall be chrome-plated type with ball valve .

U上Al，Ti/Al镀层研究

Study on Al , Ti / Al Bilayers Coatings on Uranium Substrates

铀表面Cu、Ni-P/Cu镀层研究

Study on Ni-P / Cu Coatings on U substrates

Ni-P-纳米Al2O3复合镀层耐磨性能研究

Study on the wear resistance performance of Ni-P-nano-Al_2O_3 composite coatings

电流密度和润湿剂对Ni镀层组织与形貌的影响

Effects of Current Density and Wetting Agent on the Nickel Coating by Electroplating

并用SEM，XRD研究锌镀层的微观结构。

The microstructure of zinc coatings was studied by SEM and XRD .

研究了温度、电流密度、pH等工艺条件对镍-金刚石复合镀层性能的影响。

The Influences of process conditions , such as temperature , current density , pH value , etc.

用X射线荧光光谱法测定了Fe基上Zn镀层的质量厚度；

The thickness of Zn coating on Fe substrate was measured by X-ray fluorescence spectrometry .

通过SEM对镀层的形貌和组成进行了观测。

Morphology and composition of the electroless nickel plating coating was observed by SEM .

研究了化学镀Co－P合金镀层中磷含量与工艺条件的关系及产生非品结构的成分条件。

The relation between phosphorus content and the electroless CoP alloy plating conditions to form amorphous structure has been investigated .

纳米Al2O3颗粒含量对复合镀层组织和滑动磨损行为的影响

Effects of Al_2O_3 Nanoparticle Content on Structure and Sliding Wear Behavior of the Composite Plating

镀层厚度应与siC微粒粒度相当。

The thickness of coating should be suitable with the size of SiC particles .

Ni-P-W-α-Al2O3复合镀层工艺及性能研究

Study on Performance and Process of Ni-P-W - α - Al_2O_3 Composite Coatings

纳米和微米La2O3颗粒增强镍基复合镀层的摩擦磨损性能

Friction and Wear Properties of Nano-and Micron-sized La_2O_3 Particles Reinforced Ni Matrix Composite Coatings

Ni基纳米Si3N4复合镀层的超声-电沉积工艺研究

Study on technology of ultrasonic-electrodeposited Ni-nano Si_3N_4 composite coatings

合金沉积层的显微硬度随镀层中的W含量提高而增大。

The microhardness of the alloy deposit increases with the raise of tungsten content in the deposit .

镍基Si3N4复合镀层的摩擦磨损特性

Friction and Wear Properties of Nickel Based Si_3N_4 Composite Coatings

Ni-（Mo）-P/Cu多层交替镀层的制备及其热稳定性

Preparation and Thermal Stability of Ni ( - Mo ) - P / Cu Alternate Multilayers

通过电镀法制备了功能梯度Ni-P合金镀层。

The function gradient Ni-P alloy deposit was prepared by plating .

Ni-P基多元合金镀层的耐腐蚀磨损性能

The Corrosion - wear Resistance of the Ni-P Polybasic Composite Coating

研究了Ni－W合金镀层的抗高温氧化及镀层加热处理后的硬度。

This paper studied the high-temperature oxidation resistance and the hardness after heat treatment on amorphous Ni-W alloy deposition .

Ni基与Ni-P基含MoS2复会电刷镀层的减摩特性

Study on friction-reducing property of MoS_2-containing Ni base and Ni-P base composite brush plating layers

高耐蚀性的双层化学镀Ni-P合金镀层

High Performance Corrosion Resistance Double Layer Chemical Ni-P Alloy Plating

SEM实验表明，镀层表面形貌为团粒状，颗粒大小较不均匀。

SEM experiment displays that the deposit has a ( surface ) morphology of granular structure with uneven grain sizes .

电刷镀含纳米SiC粉复合镀层的EPMA分析

EPMA Analysis of Brush-plating Ni / nano-SiC Composite Coating

随着沉积电流密度的提高，镀层中W的含量增大，而沉积电流效率降低。

When deposition current density was increased , W content in the coating was raised and deposition current efficiency decreased .

通过化学镀方法制备高硬度NiB及NiMoB合金镀层。

High hardness Ni B and Ni Mo B coatings are prepared by EN with potassium borohydride reducing agent .

化学镀Ni-P合金镀层相结构与硬度的研究

Studies on Relationship between Structure and Hardness of Ni-P Alloy Coating by Electroless Plating