后道工序

  • 网络Subsequent process;back-end production
后道工序后道工序
  1. LF精炼及后道工序钢中氮、氧含量控制技术研究

    Study on Controlling Nitrogen and Oxygen Content in Liquid Steel during LF Refining and Later Sequence

  2. 对环锭纺后道工序产生纱疵的分析与控制

    Analyses and Controling the Yarn Faults of the Last Ring Spinning Process

  3. 瓦楞纸箱后道工序是纸箱生产的重要组成部分。

    Corrugated carton production following process is an important part .

  4. 浆纱是在纺织生产工序中非常重要的一环,浆纱质量的好坏在很大程度上决定了后道工序中织造效率高低以及成品质量和档次。

    Sizing is a very important process during the making of textile production and the weaving efficiency and the quality of fabric are mostly decided by the sizing .

  5. 上海市新办纸箱企业基本上采用购买纸板加工后道工序生产纸箱的模式,投资少、产出快、成本低、效益好。

    New Shanghai Office to purchase cardboard carton business is essentially using the following process of production processing mode carton , less investment , output speed , low cost-effective .

  6. 圆形的交联聚乙烯绝缘线芯在成缆时都要用填充材料填充空隙,无形中增加了电缆外径,也增加了后道工序的材料用量。

    XLPE cables consists of round XLPE insulated conductors need filler to fill the interstices between conductors , which adds the cable overall diameter and the material usage in the next process .

  7. 集聚纺纱可消除传统环锭纺纱的加捻三角区,从而减少纱线的毛羽、提高纱线强力和弹性、减少纺纱断头,便于后道工序加工。

    The Compact Spinning can eliminate the twist triangle of the conventional Ring Spinning , so as to decrease the hairiness of yarns , increase tensile strength and elastic perfor-mance , decrease the breakage during the spinning .

  8. 在纺织机械中,并纱机是用来将络筒机络成的棉、毛及其他化纤混纺的单纱筒子并合成股纱筒子,供倍捻等后道工序使用。

    In the textile industry , the doubling machine is used to combine several single yarn tubes which are blended by cotton , wools and other fibers from winding machine to muti-yarn for the use of next processes such as twist .

  9. 分析了在后道加工工序中重要的参数。

    The important parameters in the individual downstream processing stages are analyzed .

  10. 本文应用全面质量管理的思想,详细论述了该厂铁合金产品形成过程中前、中、后三道工序的质量管理方法。

    In the light of T.Q.C.quality management methods in the former , middle and latter three working procedures during the products forming in the Co Ltd are stated in detail .

  11. 分析了镀锌彩钝膜结合力差的原因,并提出了解决办法,包括严格执行镀锌彩钝工艺操作条件及工艺流程、加强镀后各道工序清洗以及严格控制光亮剂的添加。

    The reasons of poor adhension for the color passivate films were analyzed , and the corresponding solutions were also promoted , including complying with the operation conditions and process flow severely , strengthening rinse steps after plating and controlling brightener addition severely .

  12. 报专检检查合格后转入下道工序。

    Start the next process after the special inspection is qualified .

  13. 烧毛按照传统是机织棉布后处理的第一道工序。

    Singeing is traditionally the first finishing process for woven cotton cloth .