过盈量

  • 网络magnitude of interference;interference
过盈量过盈量
  1. 双层圆挤压筒过盈量参数优化设计和分析

    Parameter-Optimizing Design and Analysis of Magnitude of Interference for Double-Layer Cylindrical Extrusion Chamber

  2. 汽车水泵轴承密封圈的密封性能与唇口过盈量密切相关。

    The performance of automotive water pump bearing seal is closely related with the magnitude of interference of the sealing lip .

  3. VC轧辊心轴与辊套过盈量的确定

    Determination on amount of interference between mandrel and roller sleeve of variable crown roller

  4. 辊套与心轴之间的过盈量δ,是VC(VariableCrown)轧辊系统的关键结构参数之一。

    The amount of interference d between roller sleeve and mandrel is one of the key structural parameters of variable crown ( VC ) roller system .

  5. 在此基础上,进一步通过有限元模拟,分析了轴向预紧力的大小,公差及过盈量的变化对HSK刀具联接系统性能的影响。

    Finally , influence of interference and axial preload on the performance of HSK tool interface has been surveyed .

  6. 本文将针对线圈骨架上下部进行有限元建模,选取不同的尺寸参数及过盈量对其采用有限元接触分析,得出VONMISES应力最大值。

    This article will coil up and down for the Ministry of finite element modeling , select a different size parameters and the amount of interference using the finite element contact analysis of its , maximum Von Mises stress obtained .

  7. 通过对800mm甲醇合成塔热套过盈量的计算和工艺控制过程分析,给出了最佳的过盈量和可靠的工艺参数。

    The optimum distance beyond the limitation for thermowell and the reliable process parameter were put forward after the calculation of the distance beyond the limitation of thermowell of methanol synthesis tower ( 800mm ) and the analysis of process control .

  8. 16A链板合理过盈量为0.06~0.08mm,相对无过盈时其疲劳强度可提高40%~50%。

    It is obtained that the reasonable shrink range for Type 16A chain is from 0.06 mm to 0.08 mm . The fatigue strength at this value increases by 40 % to 50 % compared with that of no shrink range .

  9. 环境温度变化对安装过盈量的影响

    Influence upon Interference at Installation by the Changing of Ambient Temperature

  10. 热套压力容器半径过盈量的优化设计

    Optimum Design of the Radial Interference Magnitude of Shrunk Pressure Vessels

  11. 旋转密封○形圈最小过盈量的确定

    Determination of Minimum Compression of O - ring for Rotating Sealing

  12. 密珠轴承过盈量的分析与计算

    Analysis and Calculation of Magnitude of Interference of Close-Packed Ball Bearings

  13. 这些结果,对过盈量的选择也有参考价值。

    These results are useful in the optimum design of interference fitting .

  14. 金属橡胶密封构件最小过盈量的研究

    Research on the Minimum Interference of Metal Rubber Sealing Component

  15. 螺旋桨液压套合过盈量的可靠性设计

    The Over Surplus Quantity Reliability Design of Hydraulic Pressure Sheath Screw Propeller

  16. 石油套管气密接头密封过盈量的分析与计算

    Analysis and calculation for the sealed surplus of airtight coupling for oil pipe

  17. 关于缩套圆筒过盈量的研究

    The research on amount of interference for shrink-on cylinder

  18. 确定了过盈量及装配预紧力的关系。

    Confirmed the relationship between the shrink range and the assembly pretightening force .

  19. 高速电主轴轴承配合过盈量的计算方法研究

    Calculation Method Research of the Interference Fit for High Speed Motorized Spindle Bearings

  20. 车速对纸机空心铸铁辊过盈量设计的影响

    Effects of Paper-Machine Speed on the Design of Interference Values of Hollow Iron Rolls

  21. 无键联接过盈量的合理选择及应用

    Reasonable Choice and Application of Non-key Coupling Interference

  22. 甲醇合成塔热套过盈量的工艺控制

    Process control for the distance beyond the limitation of thermowell of methanol synthesis tower

  23. 在不同过盈量条件下,对孔轴过盈配合接触面径向应力的分布进行了研究和比较。

    The influence of different amounts of interference on the radial compressive stress is analyzed .

  24. 提高过盈量可以很好地解决该问题,从而提高加工精度。

    The large interference is enough to solve this problem , and thereby improves machining accuracy .

  25. 还介绍了计算过盈量的方法和步骤,并列举了工程计算实例加以说明。

    This article presents the procedure for calculating the interference range and cites some engineering examples .

  26. 电力机车整体辗钢车轮压装过盈量的研究

    Study on Assemble Shrink Range of Mono - bloc Wrought Steel Wheel - set of Electric Locomotive

  27. 介绍了密封面角度、过盈量等关键参数的确定过程。

    The determination of the angle , interference and other key parameters of the sealing surface were introduced .

  28. 联轴器和矫直辊轴的装配过盈量对应力的影响

    The Effect of Interference Amount Between Coupling and Axis of Straightening Roller in the Aspect of the Stress

  29. 大型压缩机组用闭式叶轮多采用轴与轮毂全接触形式进行热装,过盈量一般按经验值选取。

    The heating assembly is generally applied for the closed impeller wheel and axle in the large-scale compressor group .

  30. 螺栓螺纹段的变形机制随轴向位置的不同而变化,且与中径过盈量有关;

    The deformation mechanism of the threaded segment is changeable with the axial position and dependent on the radial interference sizes ;